Sponsored Content
Operating Systems HP-UX routing issues with multiple NIC cards Post 302208287 by 411seeker on Monday 23rd of June 2008 02:02:54 PM
Old 06-23-2008
You do not need special routes for these. They get automatically created when you add the interface.

Think about it.. how do I get to the 12399.8.0 net, I go out the 123.99.8.234 interface.

The only route that counts in your config is the default going down 123.99.3.234 interface

If traffic from some other net ( e.g 192.168.4.1 )comes in on the 123.99.8.234 net it will be returned to the router via the 123.99.3.234 LAN unless you add a statement like this.

route add 192.168.4.0 123.99.8.254 1

It is the extranets you want to set the routes for. Same nets will always go out the proper LAN and get routes added automatically as part of ifconfig.
 

10 More Discussions You Might Find Interesting

1. Solaris

NIC cards for sunblade 100

I need to add a PCI NIC to a sunblade 100 running solaris 8. Im new to this and was hoping someone could give me some card names and models which will work for this system and has a driver for this sparc system. thanks (3 Replies)
Discussion started by: meyersp
3 Replies

2. IP Networking

Setup 2 NIC cards in one UNIX system

Hi; I have a UNIX box (SCO 5.0.2) with two (2) NIC cards. One card (NIC1) talks to a network 57.14.65.x/27. The other card NIC2) talks to users on 57.14.103.x and 57.14.105.x with subnet mask of 255.255.0.0. If I set NIC2 to this subnet mask (255.255.0.0) it seems like the NIC traffic is now... (2 Replies)
Discussion started by: texaspanama
2 Replies

3. High Performance Computing

veritas and nic cards

Hello I have 2 machines with 3 NIC cards. When I setup veritas, I receive this message: e1000g1 has an IP address configured on it. It could be a public NIC on ken. Are you sure you want to use e1000g1 for the first private heartbeat link? As if e1000g1 should not have an IP address.... (2 Replies)
Discussion started by: melanie_pfefer
2 Replies

4. Red Hat

External NIC cards not pinging with each other in RHEL 5.1

We have a setup of two nodes which has two NIC cards in each. One is built in and another is D-Link (external NIC card). We are unable to ping to the external NIC cards in both. Eg: Node A has two IPs 192.168.1.10 (eth0) and 192.168.2.10 (eth1) and Node B has two IPs 192.168.1.20 (eth0) and... (3 Replies)
Discussion started by: durgaprasadr13
3 Replies

5. Solaris

Network cards - Routing

Hi all I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem. So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1).... (2 Replies)
Discussion started by: sbk1972
2 Replies

6. HP-UX

HP UX 9000 NIC CARDS

Hello, I am trying to move an HP UX from one locaion to another. The new location don't have any Fiber switches. On the back of my server I see 2 RJ 45 for console management the other for networking , the server also has a fiber NIC card. When I disconnec the fiber and want to user regular... (1 Reply)
Discussion started by: ldaliosmane
1 Replies

7. UNIX for Advanced & Expert Users

Solaris 10 routing table issues

Hello Hope someone can help with this problem. We are running Solaris 10 with a current kernel patch of 142900-09. We appear to be getting a serious issue with the routing table as shown below: Output from netstat -rnv Destination ....Mask ............Gateway ........Device... (2 Replies)
Discussion started by: gregsih
2 Replies

8. IP Networking

Best reference for understanding low level info on nic cards drivers and functionality

Hi, What is the best reference that gives in detail on nic cards configuration , assigning multiple ip addresses to a single interface, netlink library etc and all basic stuff at this level..? Thanks (2 Replies)
Discussion started by: Gopi Krishna P
2 Replies

9. Ubuntu

Help asap squid with 2 nic cards setup

I found an old post that talks about 2 nice cards and it is driven by the IP address .... but I didn't understand it because the 2 people skipped information for me the newbie.. Can someone help me... I have the proxy server setup and I believe I have enabled the 2nd nic card, I just need one... (1 Reply)
Discussion started by: trilju2005
1 Replies

10. Ubuntu

How do you setup 2 nic cards for squid Ubuntu server?

I have a made my squid proxy, I now have add another nic card to an old CPU using Ubuntu server 12.04. I have seen another post similar however I am new and did not understand some of it. Something about redirecting IP address and IP table? I don't know how to do this.:confused: (9 Replies)
Discussion started by: trilju2005
9 Replies
VDE_L3(1)						      General Commands Manual							 VDE_L3(1)

NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch. SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket] DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup for each -v option given at command line. Static routes to target networks can be defined using the -r option. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 -v /var/run/s2.ctl:10.0.0.254/255.255.0.0 connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in each network can specify the vde_l3 as their gateway to reach the other one. OPTIONS
-v vde_plug:ipaddress/netmask Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One can define as many interfaces as she wants. -r target_network/netmask:gateway Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she wants. -G default_gw Specify a default gateway, to be used whenever no static route is defined for a target host. -M mgmt_socket the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be used as a remote terminal for wirefilter. NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik" i.e. the German "Association for Electrical, Electronic & Information Technologies"). SEE ALSO
vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1). AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net> VDE is a project by Renzo Davoli <renzo@cs.unibo.it> Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)
All times are GMT -4. The time now is 12:38 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy