Sponsored Content
Full Discussion: Network problem
Special Forums IP Networking Network problem Post 302208253 by Katkota on Monday 23rd of June 2008 12:03:40 PM
Old 06-23-2008
Power Network problem

Folks;
I have 2 SUSE servers (192.168.157.100 & 192.168.157.101) both are similar and has the same gateway 192.168.157.1
I can connect to the second one from my PC just fine (192.168.157.101).
The problem is i couldn't connect to the first one using SSH even after i disabled the firewall. when i ran tracert on both from my PC, i saw that (see below).
From the output of the tracert I believe this is a gateway related. i checked every thing and i see the gateway defined the same on both servers.

Code:
C:\Documents and Settings\me>tracert -d 192.168.157.101

Tracing route to 192.168.157.101 over a maximum of 30 hops

  1    <1 ms    <1 ms    <1 ms  10.140.100.1
  2    <1 ms    <1 ms    <1 ms  10.140.200.101
  3    <1 ms    <1 ms    <1 ms  192.168.157.101

Trace complete.

C:\Documents and Settings\me>tracert -d 192.168.157.100

Tracing route to 192.168.157.100 over a maximum of 30 hops

  1    <1 ms    <1 ms    <1 ms  10.140.100.1
  2    <1 ms    <1 ms    <1 ms  10.140.200.101
  3     *        *        *     Request timed out.
  4     *        *        *     Request timed out.
  5     *        *        *     Request timed out.
  6  ^C
C:\Documents and Settings\me>

Any help will be very much appreciated rolleyes

Last edited by DukeNuke2; 06-28-2008 at 04:12 AM.. Reason: add code tags
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Network problem Unix

Changed from a broken Switch to a working HUB everyting else in my network is ok after the change but not my RS/6000! It refuses to get connected, get time out on Pings both ways - strange? Could it be some problem with ARP?:confused: (2 Replies)
Discussion started by: jolun
2 Replies

2. Solaris

Network problem.

Hi All, This is regarding problem with two servers... EX:- server1(HP) is not able to connect with proxy server server2(SUN BOX) But we can able to login.... server1 is not able to pickup any data from the proxy server... checked in the sunbox... # ping bdhp5050 server1 is alive ... (1 Reply)
Discussion started by: jeelans
1 Replies

3. SCO

Network interfaces problem

Hi, I have problems with my SCO unix network interfaces. Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot. Installed driver using SCO Software manager - successfully Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
Discussion started by: vilius
0 Replies

4. AIX

network printer problem

I have AIX 5.3 OS. After issuing the print command, the printer state immediately goes down. I have checked the /etc/qconfig flle, resatrted the qdaemon but again same problem is occuring. I am using HP 5100 connected to jetdirect. what is the problem and it's solution? (4 Replies)
Discussion started by: prashantchavan
4 Replies

5. Solaris

Problem in network configuration

Hi everybody, I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem. I have 2 unix machines absolutely identical running solaris 9. For network reasons I need to change the IP address of the 2 machines. I proceed exactly the same on the... (11 Replies)
Discussion started by: aribault
11 Replies

6. AIX

AIX OS problem? network problem?

Dear ALL. I installed AIX OS on customer sites. but Only one site is too slow when I connected telnet, ftp.. Ping is too fast. but telnet and FTP is not connected.. of course i check the configuration file on aix but it's normal. Do any Idea?? thanks in advance. - Jun - (3 Replies)
Discussion started by: Jeon Jun Seok
3 Replies

7. Solaris

Network interface problem

Hi i have replace a NIC card on solaris 10 when i give the following command ifconfig -a it just show the lo0 (only loop back with inet 127.0.0.1) when i give the following command to config the interface, ifconfig elxl0 plumb ifconfig: plumb: elxl0: no such interface please help... (11 Replies)
Discussion started by: malikshahid85
11 Replies

8. AIX

Network Problem

Hi everbody; I have 2 p520 machines and created a vio server for each one (vio01 - vio02). I created 3 AIX 5.3 lpars on vio02 and 3 AIX 6.1 lpars on vio01. The problem is when 2 lpars are activated, i can ping gateway from both lpars and vio; but when i activate 3rd lpar, network downs and none of... (2 Replies)
Discussion started by: lordofdarkness
2 Replies

9. Debian

/etc/network/interfaces problem

Hello i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address then i save it wq! then i restart the networking , /etc/init.d/networking restart . but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Discussion started by: learn82
5 Replies

10. Android

Problem with wireless network

Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies
VDE_L3(1)						      General Commands Manual							 VDE_L3(1)

NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch. SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket] DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup for each -v option given at command line. Static routes to target networks can be defined using the -r option. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 -v /var/run/s2.ctl:10.0.0.254/255.255.0.0 connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in each network can specify the vde_l3 as their gateway to reach the other one. OPTIONS
-v vde_plug:ipaddress/netmask Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One can define as many interfaces as she wants. -r target_network/netmask:gateway Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she wants. -G default_gw Specify a default gateway, to be used whenever no static route is defined for a target host. -M mgmt_socket the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be used as a remote terminal for wirefilter. NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik" i.e. the German "Association for Electrical, Electronic & Information Technologies"). SEE ALSO
vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1). AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net> VDE is a project by Renzo Davoli <renzo@cs.unibo.it> Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)
All times are GMT -4. The time now is 01:24 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy