Folks;
I have 2 SUSE servers (192.168.157.100 & 192.168.157.101) both are similar and has the same gateway 192.168.157.1
I can connect to the second one from my PC just fine (192.168.157.101).
The problem is i couldn't connect to the first one using SSH even after i disabled the firewall. when i ran tracert on both from my PC, i saw that (see below).
From the output of the tracert I believe this is a gateway related. i checked every thing and i see the gateway defined the same on both servers.
Any help will be very much appreciated rolleyes
Last edited by DukeNuke2; 06-28-2008 at 04:12 AM..
Reason: add code tags
Changed from a broken Switch to a working HUB everyting else in my network is ok after the change but not my RS/6000! It refuses to get connected, get time out on Pings both ways - strange?
Could it be some problem with ARP?:confused: (2 Replies)
Hi All,
This is regarding problem with two servers...
EX:- server1(HP) is not able to connect with proxy server server2(SUN BOX)
But we can able to login.... server1 is not able to pickup any data from the proxy server...
checked in the sunbox...
# ping bdhp5050
server1 is alive
... (1 Reply)
Hi,
I have problems with my SCO unix network interfaces.
Intel integrated adapter was failing, so I installed new one - 3COM adapter into free PCI slot.
Installed driver using SCO Software manager - successfully
Added new Network adapter using SCO Network configuration manager - successfully... (0 Replies)
I have AIX 5.3 OS. After issuing the print command, the printer state immediately goes down. I have checked the /etc/qconfig flle, resatrted the qdaemon but again same problem is occuring. I am using HP 5100 connected to jetdirect.
what is the problem and it's solution? (4 Replies)
Hi everybody,
I have a very strange problem ; if somebody could help me it would be very kind. I'll try to explain my problem.
I have 2 unix machines absolutely identical running solaris 9.
For network reasons I need to change the IP address of the 2 machines.
I proceed exactly the same on the... (11 Replies)
Dear ALL.
I installed AIX OS on customer sites.
but Only one site is too slow when I connected telnet, ftp..
Ping is too fast. but telnet and FTP is not connected..
of course i check the configuration file on aix but it's normal.
Do any Idea??
thanks in advance.
- Jun - (3 Replies)
Hi
i have replace a NIC card on solaris 10 when i give the following command
ifconfig -a
it just show the lo0 (only loop back with inet 127.0.0.1)
when i give the following command to config the interface,
ifconfig elxl0 plumb
ifconfig: plumb: elxl0: no such interface
please help... (11 Replies)
Hi everbody;
I have 2 p520 machines and created a vio server for each one (vio01 - vio02). I created 3 AIX 5.3 lpars on vio02 and 3 AIX 6.1 lpars on vio01. The problem is when 2 lpars are activated, i can ping gateway from both lpars and vio; but when i activate 3rd lpar, network downs and none of... (2 Replies)
Hello
i am configuring a debian lenny sever ,/etc/network/interfaces is modified so that eth1 takes a static IP address
then i save it wq!
then i restart the networking , /etc/init.d/networking restart .
but after reboot ,the file is reset ,note that the interfaces had by defauklt IPv6 address... (5 Replies)
Good day, everybody! I have a mobile phone (LG Optimus L5) with Android 4.0.3 and a tablet (PocketBook SurfPad 2) with Android 4.1.1 and I have problem with wireless network on these devices. Laptops don't have such problem. My wireless network organisation is a modem connected with an access point... (11 Replies)
Discussion started by: qzxcvbnm
11 Replies
LEARN ABOUT SUSE
aggregate-ios
AGGREGATE-IOS(1) General Commands Manual AGGREGATE-IOS(1)NAME
aggregate-ios - optimise a concatenated set of cisco/IOS prefix filters to help make them nice and short.
SYNOPSIS
aggregate-ios <source_config >optimised_config
DESCRIPTION
Takes cisco IOS configuration on stdin, and optimises any prefix filters found using aggregate(1). Optimised filters are produced on std-
out.
OPTIONS
None.
DIAGNOSTICS
Any diagnostics produced by aggregate(1) are passed through on stderr.
EXAMPLES
The following configuration fragment:
ip prefix-list AS65530 description Foo, Inc
ip prefix-list AS65530 permit 10.1.0.0/16
ip prefix-list AS65530 permit 10.2.0.0/16
ip prefix-list AS65530 permit 10.2.1.0/24
ip prefix-list AS65530 permit 10.3.0.0/16
ip prefix-list AS65531 description Bar.Com
ip prefix-list AS65531 seq 5 permit 192.168.1.0/24
ip prefix-list AS65531 seq 10 permit 192.168.2.0/24
ip prefix-list AS65531 seq 15 permit 192.168.0.0/19
is optimised as follows:
ip prefix-list AS65530 permit 10.1.0.0/16 le 24
ip prefix-list AS65530 permit 10.2.0.0/15 le 24
ip prefix-list AS65531 permit 192.168.0.0/19 le 24
SEE ALSO aggregate(1)HISTORY
Aggregate-ios was written by Joe Abley <jabley@mfnx.net>.
BUGS
All those in aggregate(1) and then some :)
Joe Abley 2000 November 27 AGGREGATE-IOS(1)