06-23-2008
Have you filled correctly /etc/rc.config.d/netconf file?
After the stanzas for your multiple lans, there is another section
for all the routings for EACH lan you have (lan[0] [1] etc) you will have to copy the block and configure for each lan interface if not yet done...
10 More Discussions You Might Find Interesting
1. Solaris
I need to add a PCI NIC to a sunblade 100 running solaris 8. Im new to this and was hoping someone could give me some card names and models which will work for this system and has a driver for this sparc system.
thanks (3 Replies)
Discussion started by: meyersp
3 Replies
2. IP Networking
Hi;
I have a UNIX box (SCO 5.0.2) with two (2) NIC cards. One card (NIC1) talks to a network 57.14.65.x/27. The other card NIC2) talks to users on 57.14.103.x and 57.14.105.x with subnet mask of 255.255.0.0. If I set NIC2 to this subnet mask (255.255.0.0) it seems like the NIC traffic is now... (2 Replies)
Discussion started by: texaspanama
2 Replies
3. High Performance Computing
Hello
I have 2 machines with 3 NIC cards.
When I setup veritas, I receive this message:
e1000g1 has an IP address configured on it. It could be a public NIC on ken.
Are you sure you want to use e1000g1 for the first private heartbeat link?
As if e1000g1 should not have an IP address.... (2 Replies)
Discussion started by: melanie_pfefer
2 Replies
4. Red Hat
We have a setup of two nodes which has two NIC cards in each. One is built in and another is D-Link (external NIC card). We are unable to ping to the external NIC cards in both. Eg: Node A has two IPs 192.168.1.10 (eth0) and 192.168.2.10 (eth1) and Node B has two IPs 192.168.1.20 (eth0) and... (3 Replies)
Discussion started by: durgaprasadr13
3 Replies
5. Solaris
Hi all
I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem.
So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1).... (2 Replies)
Discussion started by: sbk1972
2 Replies
6. HP-UX
Hello,
I am trying to move an HP UX from one locaion to another. The new location don't have any Fiber switches.
On the back of my server I see 2 RJ 45 for console management the other for networking , the server also has a fiber NIC card. When I disconnec the fiber and want to user regular... (1 Reply)
Discussion started by: ldaliosmane
1 Replies
7. UNIX for Advanced & Expert Users
Hello
Hope someone can help with this problem. We are running Solaris 10 with a current kernel patch of 142900-09.
We appear to be getting a serious issue with the routing table as shown below:
Output from netstat -rnv
Destination ....Mask ............Gateway ........Device... (2 Replies)
Discussion started by: gregsih
2 Replies
8. IP Networking
Hi,
What is the best reference that gives in detail on nic cards configuration , assigning multiple ip addresses to a single interface, netlink library etc and all basic stuff at this level..?
Thanks (2 Replies)
Discussion started by: Gopi Krishna P
2 Replies
9. Ubuntu
I found an old post that talks about 2 nice cards and it is driven by the IP address .... but I didn't understand it because the 2 people skipped information for me the newbie..
Can someone help me... I have the proxy server setup and I believe I have enabled the 2nd nic card, I just need one... (1 Reply)
Discussion started by: trilju2005
1 Replies
10. Ubuntu
I have a made my squid proxy, I now have add another nic card to an old CPU using Ubuntu server 12.04. I have seen another post similar however I am new and did not understand some of it. Something about redirecting IP address and IP table?
I don't know how to do this.:confused: (9 Replies)
Discussion started by: trilju2005
9 Replies
lan(7) Miscellaneous Information Manual lan(7)
NAME
lan - network I/O card access information
DESCRIPTION
This manual entry gives a brief description on how to access the LAN device driver at Layer 2 (Data Link Layer) of the OSI architecture.
The LAN device driver controls the various LAN interface cards (e.g, Ethernet/IEEE 802.3, FDDI, Token Ring) at Layer 1 (Physical Layer).
The Data Link Provider Interface (DLPI) is the supported method for accessing the LAN device driver at Layer 2. DLPI is intended for use
by knowledgeable network users only. Refer to the for complete programming details.
There are HP and non-HP drivers and interface cards which will provide their own DLPI module. These types of DLPI are referred to as
"native" DLPI.
Overview
The Physical Point of Attachment (PPA) is a numerical value that uniquely identifies a particular device. The PPA value can be obtained
from the and commands. The "ClassInstance" identifier in the output is the concatenation of the driver class (lan) and the PPA number.
The "NamePPA" identifier in the output is a concatenation of the interface name and the PPA number. The value for a lan device is equiva-
lent to the PPA number for that device.
A single hardware device may have multiple "NamePPA" identifiers, which indicates multiple encapsulation methods supported for to the
device. For Ethernet/IEEE 802.3 links, the "Name" is used to designate Ethernet encapsulation, and for IEEE 802.3 encapsulation. For
other links (FDDI, Token Ring), only the encapsulation designation is used.
Methods of transfer over the DLPI interface through the lan devices include "raw", "connectionless", and "connection-oriented" data trans-
fers.
WARNINGS
The and commands are deprecated. These commands will be removed in a future HP-UX release. HP recommends the use of replacement command
nwmgr(1M) to perform all network interface-related tasks.
AUTHOR
was developed by HP.
SEE ALSO
lanscan(1M), lanadmin(1M), linkloop(1M), nwmgr(1M).
1995, Hewlett-Packard
Version 2.0, November 1982, Digital Equipment Corporation, Intel Corporation, Xerox Corporation
1996, Institute of Electrical and Electronic Engineers
1996, Institute of Electrical and Electronic Engineers
1995, ANSI
1995, Institute of Electrical and Electronic Engineers
1995, Institute of Electrical and Electronic Engineers
lan(7)