06-12-2008
A good place to start looking would be the routing table. Issue a "netstat -r" and have a look t the routing rules. Probably the interface connecting to the internet is set as default route.
To switch off IPng use SMIT to change the properties of the IP stack.
bakunin
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
hello
i'm working on aix 5300-05-03 hacmp ver 5.4
well my issue is that when firewall (gateway to internet ) goes down my machine start to work very very slowly!!!
the output of the sniffer is that on the output card , my machine try to convert ipv4 to ipv6 0.0.2.0
my machine is not configure... (1 Reply)
Discussion started by: ariec
1 Replies
2. IP Networking
Need help...!
I want to configure Samba 3 for IPv6 operation with Window XP for IPv4.
I appreciate any guide.
Thanks
HSV (0 Replies)
Discussion started by: Sovan
0 Replies
3. Solaris
Hi folks, i hope you'll help me to configure my ipv6 tunnel.
First, i create my tunnel in:
Hurricane Electric Free IPv6 Tunnel Broker
My IP is 83.228.93.34
in HE:
------------------------
Server IPv4 address: 216.66.84.46
Server IPv6 address: 2001:470:1f14:16a::1/64
Client IPv4 address: ... (2 Replies)
Discussion started by: static
2 Replies
4. Shell Programming and Scripting
I have perl script that I use to check and ping a list of ip,
The problem is, I didnt understand how to ping ipv6 on perl,
Could I use Ping::External??And how could I get the ping result (reply or not)?
This is my code
#!/usr/bin/perl --
use Net::Ping;
use Data::Validate::IP;
use... (3 Replies)
Discussion started by: franzramadhan
3 Replies
5. Red Hat
Hello,
I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch.
I think it should be fine but I would like to hear out your comments. (1 Reply)
Discussion started by: svalenciatech
1 Replies
6. Solaris
Hi
I am looking to set-up ISC DHCP to support ipv6, and to migrate my existing SUN DHCP ipv4 to ISC,
finding the ipv4 options for the SUN DHCP options was ok eg
TFTPsrvN = tftp-server-name
OptBootF = bootfile-name
However if I set up a DHCPv6 does anyone know what the equivalent... (1 Reply)
Discussion started by: eeisken
1 Replies
7. AIX
Hi all,
I have setup ipv6 in AIX machine using autoconf6 command.
I was successfull in doing this. after execution of the command local link address was assigned to one of the interfaces
(en1).But I have to setup the following environment as well.
1) Machine with only IPv6 support(IPv4... (0 Replies)
Discussion started by: ard
0 Replies
8. Solaris
Hi,
I am looking for a solution to configure ntp between ipv4 ( ntp server ) to ipv6 ( client) .
I had google, but lot many sites suggest to have dual stock or tunnaling.
my issue is I have client has only ipv6 address ans server has ipv4 address. is it possible to sync time,... (4 Replies)
Discussion started by: naveen.surisett
4 Replies
9. Solaris
Hello dears
how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies
LEARN ABOUT DEBIAN
ipkungfu
ipkungfu(8) System Manager's Manual ipkungfu(8)
NAME
ipkungfu - An iptables-based firewall for Linux
SYNOPSIS
ipkungfu [ -c ] [ -t ] [ -d ] [ -h ] [ -v ] [ --quiet ] [ --panic ] [ --no-caching
DESCRIPTION
ipkungfu is an iptables-based Linux firewall. The primary design goals are security, ease of use, and performance, in that order. It takes
advantage of advanced features of iptables, tcpwrappers, and the Linux kernel. It also simplifies the configuration of internet connection
sharing, advanced routing, and other networking needs.
OPTIONS
-c (or --check)
Check whether ipkungfu is loaded, and report any command line options it may have been loaded with.
-t (or --test)
Runs a configuration test, and displays the results. Note that this does not test or display all configuration options. This
gives you an opportunity to verify that major configuration options are correct before putting them into action.
-d (or --disable)
Disables the firewall. It is important to know exactly what this option does. All traffic is allowed in and out, and in the
case of a gateway, all NATed traffic is forwarded (the option retains your connection sharing options). Custom rules are not
implemented, and deny_hosts.conf is ignored.
-f (or --flush)
Disables the firewall COMPLETELY. All rules are flushed, all chains are removed. Any port forwarding or internet connection
sharing will cease to work.
-h (or --help)
Displays brief usage information and exits.
-v (or --version)
Displays version information and exits.
--quiet Runs ipkungfu with no standard output
--panic Drops ALL traffic in all directions on all network interfaces. You should probably never use this option. The --panic option
is available for the highly unusual situation where you know that an attack is underway but you know of no other way to stop
it.
--failsafe If ipkungfu fails, --failsafe will cause all firewall policies to revert to ACCEPT. This is useful when working with ipkungfu
remotely, to prevent loss of remote access due to firewall failure.
--no-caching
Disables rules caching feature.
FILES
/etc/ipkungfu/ipkungfu.conf
/etc/ipkungfu/advanced.conf
/etc/ipkungfu/accept_hosts.conf
/etc/ipkungfu/deny_hosts.conf
/etc/ipkungfu/custom.conf
/etc/ipkungfu/log.conf
/etc/ipkungfu/redirect.conf
/etc/ipkungfu/services.conf
/usr/sbin/ipkungfu
/usr/share/doc/ipkungfu/AUTHORS
/usr/share/doc/ipkungfu/README
/usr/share/doc/ipkungfu/FAQ
/usr/share/doc/ipkungfu/ChangeLog
/usr/share/doc/ipkungfu/COPYING
SEE ALSO
iptables(8).
January 2003 ipkungfu(8)