How to configure Samba 3 for IPv6 operation with Window XP for IPv4

Login or Register for Dates, Times and to Reply

Thread Tools Search this Thread
Special Forums IP Networking How to configure Samba 3 for IPv6 operation with Window XP for IPv4
# 1  
How to configure Samba 3 for IPv6 operation with Window XP for IPv4

Need help...!
I want to configure Samba 3 for IPv6 operation with Window XP for IPv4.
I appreciate any guide.


Login or Register for Dates, Times and to Reply

Previous Thread | Next Thread
Thread Tools Search this Thread
Search this Thread:
Advanced Search

Test Your Knowledge in Computers #28
Difficulty: Easy
Unix was the first fully supported 64-bit operating system for personal computers.
True or False?

9 More Discussions You Might Find Interesting

1. Solaris

How to assign IPv4 and IPv6 addresses with same interface?

Hello dears how to assign IPv4 and IPv6 addresses with same interface on solaris 10 (1 Reply)
Discussion started by: ttashman
1 Replies

2. Solaris

Ntp between ipv4 and ipv6

Hi, I am looking for a solution to configure ntp between ipv4 ( ntp server ) to ipv6 ( client) . I had google, but lot many sites suggest to have dual stock or tunnaling. my issue is I have client has only ipv6 address ans server has ipv4 address. is it possible to sync time,... (4 Replies)
Discussion started by: naveen.surisett
4 Replies

3. AIX

IPv6/IPv4 Only in AIX

Hi all, I have setup ipv6 in AIX machine using autoconf6 command. I was successfull in doing this. after execution of the command local link address was assigned to one of the interfaces (en1).But I have to setup the following environment as well. 1) Machine with only IPv6 support(IPv4... (0 Replies)
Discussion started by: ard
0 Replies

4. Solaris

ISC DHCP ipv4 and ipv6 options

Hi I am looking to set-up ISC DHCP to support ipv6, and to migrate my existing SUN DHCP ipv4 to ISC, finding the ipv4 options for the SUN DHCP options was ok eg TFTPsrvN = tftp-server-name OptBootF = bootfile-name However if I set up a DHCPv6 does anyone know what the equivalent... (1 Reply)
Discussion started by: eeisken
1 Replies

5. Red Hat

IPv4 and IPv6 Related Question to CentOS VMs

Hello, I was wondering if it would be possible to run two VMs one with services for IPv4 and the other one with services for IPv6. The main physical system would be connected to a IPv6 switch. I think it should be fine but I would like to hear out your comments. (1 Reply)
Discussion started by: svalenciatech
1 Replies

6. Shell Programming and Scripting

[ASK] How to check whether ipv4 or ipv6 and ping those IP

I have perl script that I use to check and ping a list of ip, The problem is, I didnt understand how to ping ipv6 on perl, Could I use Ping::External??And how could I get the ping result (reply or not)? This is my code #!/usr/bin/perl -- use Net::Ping; use Data::Validate::IP; use... (3 Replies)
Discussion started by: franzramadhan
3 Replies

7. Solaris

(Help) IPv6 tunneling over existing IPv4 in Solaris

Hi folks, i hope you'll help me to configure my ipv6 tunnel. First, i create my tunnel in: Hurricane Electric Free IPv6 Tunnel Broker My IP is in HE: ------------------------ Server IPv4 address: Server IPv6 address: 2001:470:1f14:16a::1/64 Client IPv4 address: ... (2 Replies)
Discussion started by: static
2 Replies

8. AIX

convert ipv4 ti ipv6

hello i'm working on AIX 5300-05-03 P520 hacmp 5.4 when connection to the internet is going down , firewall down, my application work verey verey slowly!!! and on the sliffer output i'm got trys of my serevr to do convert from ipv4 ipv6 ( and AAAAAAAA). some one have an idea why... (1 Reply)
Discussion started by: ariec
1 Replies

9. UNIX for Advanced & Expert Users

convert from ipv4 to ipv6

hello i'm working on aix 5300-05-03 hacmp ver 5.4 well my issue is that when firewall (gateway to internet ) goes down my machine start to work very very slowly!!! the output of the sniffer is that on the output card , my machine try to convert ipv4 to ipv6 my machine is not configure... (1 Reply)
Discussion started by: ariec
1 Replies
NDRDUMP(1)						    System Administration tools 						NDRDUMP(1)

ndrdump - DCE/RPC Packet Parser and Dumper SYNOPSIS
ndrdump [-c context] {pipe} {function} {in|out} {filename} ndrdump [pipe] ndrdump DESCRIPTION
ndrdump tries to parse the specified filename using Samba's parser for the specified pipe and function. The third argument should be either in or out, depending on whether the data should be parsed as a request or a reply. Running ndrdump without arguments will list the pipes for which parsers are available. Running ndrdump with one argument will list the functions that Samba can parse for the specified pipe. The primary function of ndrdump is debugging Samba's internal DCE/RPC parsing functions. The file being parsed is usually one exported by wiresharks "Export selected packet bytes" function. The context argument can be used to load context data from the request packet when parsing reply packets (such as array lengths). VERSION
This man page is correct for version 4.0 of the Samba suite. SEE ALSO
wireshark, pidl AUTHOR
This utility is part of the Samba[1] suite, which is developed by the global Samba Team[2]. ndrdump was written by Andrew Tridgell. This manpage was written by Jelmer Vernooij. NOTES
1. Samba 2. Samba Team Samba 4.0 06/17/2014 NDRDUMP(1)

Featured Tech Videos