You'd run this at 21:00 once, and then it should take care of itself (until management notices ...)
Yes, so could I do
This is for the other people that are sometimes on-call. I would like them to be able to just type "subdaily.sh" and it adds it to at without any room to make errors.
I'm pretty "good" with batch files so that's why there may be some errors in that... But I'm new to HP-UX and this system. The previous guy left one day and I've been trying to pick it up as best as I can.
I do not have the luxery of a server that i can try on, so i had to post my qn here.
Say i have two jobs in the cron table, the jobs are scheduled 2 mins apart. Assuming the first jobs does a lot of operations and takes > 2 mins. Will the second job be executed? Will Unix actually have a queue... (3 Replies)
i need to execute 5 jobs at a time in background and need to get the exit status of all the jobs i wrote small script below , i'm not sure this is right way to do it.any ideas please help.
$cat run_job.ksh
#!/usr/bin/ksh
####################################
typeset -u SCHEMA_NAME=$1
... (1 Reply)
Hi,
I have more that 100 jobs I can run background, if I want only 4 running at ther same time, how can I write a script to control it?
Thanks
peter (0 Replies)
Hello,
I am running GNU bash, version 3.2.39(1)-release (x86_64-pc-linux-gnu). I have a specific question pertaining to waiting on jobs run in sub-shells, based on the max number of parallel processes I want to allow, and then wait... (1 Reply)
Hi
Is it possible to run different cron jobs at the same time? It appears that when I run ones at 15 min granularity that they may prevent ones running later in the day.
Should crons run at same time have impact on one another? (4 Replies)
I've scheduled few jobs using cron. But they are not running .....
What might be the possible reasons ?? Also tell me how to troubleshoot.............
Please help me .......
Thanks in Advance. (2 Replies)
Hi,
I'm running atq for a user and its showing 2 'at' jobs in the queue to start at a later time.
> atq
Is there any way i can find out the creation date/time of these jobs?
and ideally what job created them and what script(s) they are going to run?
All i can see is the job number and... (3 Replies)
I have multiple jobs and each job dependent on other job.
Each Job generates a log and If job completed successfully log file end's with JOB ENDED SUCCESSFULLY message and if it failed then it will end with JOB ENDED with FAILURE.
I need an help how to start.
Attaching the JOB dependency... (3 Replies)
on linux redhat, ubuntu systems, what reason would there be for a cron job not running at exactly the time it was scheduled to run, everytime?
meaning, if i put something in cron to run every 120 seconds (2 minutes), why is it that some times, i find that cron would sometimes run the job a few... (1 Reply)
Discussion started by: SkySmart
1 Replies
LEARN ABOUT LINUX
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)