04-22-2008
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
2. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
3. Linux
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies
4. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
5. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
6. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
7. Linux
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Discussion started by: new2prog
7 Replies
8. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
9. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT REDHAT
sndconfig
sndconfig(8) System Manager's Manual sndconfig(8)
NAME
sndconfig - configure sound card for use with Linux kernel modules
SYNOPSIS
sndconfig {--help,--noprobe,--noautoconfig}
DESCRIPTION
sndconfig sets up the necessary configuration files to use a sound card on a Red Hat system. If PnP support is compiled in, by default snd-
config will do an initial probe for PnP sound cards using the pnpdump utility. If the --noprobe option is given this step will be skipped.
The user will be notified if any cards were found. Otherwise the user must pick the card type from a menu. Then the user must choose the
I/O port, IRQ, and DMA settings for the sound card. These must be known ahead of time and depend upon the jumper settings of the sound
card. For PnP cards, the program will determine settings for the card; if the --noautoconfig option is given the user can choose the val-
ues which will be programmed into the PnP device. There is no guarantee that the values entered do not conflict with an existing non-PnP or
PnP device. The user must make sure these types of conflicts do not occur.
OPTIONS
--help Print a usage message on standard output and exit successfully.
--noprobe
No probe will be made for PnP cards, and the PnP configuration files will not be changed.
--noautoconfig
No autoconfiguration of PnP cards will be done; the user will be prompted for settings.
FILES
/etc/sysconfig/soundcard Stores current settings /etc/modules.conf Stores sound module configuration /etc/isapnp.conf Stores
PnP configuration
SEE ALSO
isapnp(1), pnpdump(1)
Wed Aug 19 1998 sndconfig(8)