04-22-2008
on solaris 10:
dladm show-dev
dladm show-link
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
2. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
3. Linux
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies
4. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
5. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
6. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
7. Linux
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Discussion started by: new2prog
7 Replies
8. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
9. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT OPENSOLARIS
amd8111s
amd8111s(7D) Devices amd8111s(7D)
NAME
amd8111s - AMD-8111 Fast Ethernet Network Adapter driver
SYNOPSIS
/dev/amd8111s
DESCRIPTION
The amd8111s Fast Ethernet driver is a multi-threaded, loadable, clonable, GLD-based STREAMS driver supporting the Data Link Provider
Interface, dlpi(7P), on the AMD-8111 Fast Ethernet Network Adapter.
The amd8111s driver functions include controller initialization, frame transmit and receive, promiscuous and multicast support, and error
recovery and reporting.
APPLICATION PROGRAMMING INTERFACE
The cloning, character-special device /dev/amd8111 is used to access all AMD-8111 Fast Ethernet devices installed within the system.
The amd8111s driver is managed by the dladm(1M) command line utility, which allows VLANs to be defined on top of amd8111s instances and
for amd8111s instances to be aggregated. See dladm(1M) for more details.
CONFIGURATION
By default, the amd8111s driver performs auto-negotiation to select the link speed and mode. Link speed and mode can be any of the follow-
ing:
100 Mbps, full-duplex.
100 Mbps, half-duplex.
10 Mbps, full-duplex.
10 Mbps, half-duplex.
FILES
/dev/amd8111s*
Special character device.
/kernel/drv/amd8111s*
32-bit ELF kernel module (x86).
/kernel/drv/amd64/amd8111s*
64-bit ELF Kernel module (x86).
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------------------------------------+
|ATTRIBUTE TYPE ATTRIBUTE VALUE |
|Availability SUNW8111s |
|Architecture x86 |
|Interface Stability Committed |
+-----------------------------------------------------------+
SEE ALSO
dladm(1M), attributes(5), streamio(7I), dlpi(7P)
Writing Device Drivers
STREAMS Programming Guide
Network Interfaces Programmer's Guide
SunOS 5.11 30 Jul 2007 amd8111s(7D)