04-22-2008
on solaris 10:
dladm show-dev
dladm show-link
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Everyone,
While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use.
There is no output for dmesg|grep eth. Does that mean that mandrake... (2 Replies)
Discussion started by: cyno
2 Replies
2. HP-UX
using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ? (0 Replies)
Discussion started by: bobstar01
0 Replies
3. Linux
Hi PPL!
I have P-IV processor, with on-board NIC card.
I have added one more NIC card for domestic use.
My kudzu does not recognise the newly added PCMCIA NIC card.
How to go about this one?
Suggest
PEnguin (0 Replies)
Discussion started by: chakri.penguin
0 Replies
4. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
5. Solaris
Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than... (5 Replies)
Discussion started by: kurva
5 Replies
6. Solaris
I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2
When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously.
Following are the message log.
ifmsdb1 in.mpathd: NIC failure detected... (0 Replies)
Discussion started by: abhaymittal003
0 Replies
7. Linux
I have a linux box with 2 nic cards on it one for prod and one for backup.
My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion. (7 Replies)
Discussion started by: new2prog
7 Replies
8. AIX
Hi All,
How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v
Any idea?
Thanks. (2 Replies)
Discussion started by: samnyc
2 Replies
9. HP-UX
Hi,
Someone asked me the below.
If the box has multiple NIC cards, try to run a test with interface address specified as shown below
$ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress>
How can I now find out if my box has multiple NIC cards and how can I... (5 Replies)
Discussion started by: mohtashims
5 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
LEARN ABOUT OPENSOLARIS
xge
xge(7D) Devices xge(7D)
NAME
xge - Neterion Xframe 10Gigabit Ethernet Network Adapter driver
SYNOPSIS
/dev/xge
DESCRIPTION
The xge 10 Gigabit Ethernet driver is a multi-threaded, loadable, clonable, GLD-based STREAMS driver supporting the Data Link Provider
Interface, dlpi(7P), on S2IO Xframe 10-Gigabit Ethernet Network Adapter.
The xge driver functions includes controller initialization, frame transmit and receive, promiscuous and multicast support, TCP and UDP
checksum offload (IPv4 and IPv6), 9622-byte jumbo frame, and error recovery and reporting.
The xge driver and hardware support the 10GBase-SR/W, LR/W, and ER/W 802.3 physical layer.
APPLICATION PROGRAMMING INTERFACE
The cloning, character-special device /dev/xge is used to access all Xframe devices installed within the system.
The xge driver is managed by the dladm(1M) command line utility, which allows VLANs to be defined on top of xge instances and for xge
instances to be aggregated. See dladm(1M) for more details.
The values returned by the driver in the DL_INFO_ACK primitive in response to the DL_INFO_REQ are as follows:
o Maximum SDU is 9600.
o Minimum SDU is 0.
o DSLAP address length is 8 bytes.
o MAC type is DL_ETHER.
o SAP length value is -2 meaning the physical address component is followed immediately by a 2-byte sap component within the
DLSAP address.
o Broadcast address value is Ethernet/IEEE broadcast address (FF:FF:FF:FF:FF:FF).
CONFIGURATION
By default, the xge driver works without any configuration file.
You can check the running-time status of a device instance using ndd(1M). Currently, the driver provides an interface to print all hard-
ware statistics.
For example, to print statistics of device xge0:
#ndd /dev/xge0 stats
tmac_data_octets 772
tmac_frms 15
tmac_drop_frms 0
tmac_bcst_frms 6
tmac_mcst_frms 6
...
rmac_vld_frms 13
rmac_fcs_err_frms 0
rmac_drop_frms 0
rmac_vld_bcst_frms 7
rmac_vld_mcst_frms 11
rmac_out_rng_len_err_frms 0
rmac_in_rng_len_err_frms 0
rmac_long_frms 0
...
not_traffic_intr_cnt 242673
traffic_intr_cnt 28
...
FILES
/dev/xge xge special character device
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------------------------------------+
|ATTRIBUTE TYPE ATTRIBUTE VALUE |
|Architecture x86 |
+-----------------------------------------------------------+
SEE ALSO
dladm(1M), ndd(1M), attributes(5), streamio(7I), dlpi(7P)
Writing Device Drivers
STREAMS Programming Guide
Network Interfaces Programmer's Guide
SunOS 5.11 3 Oct 2005 xge(7D)