How do I find what kind of NIC card the server has? Post: 302188102

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

No NIC Card?

Hello Everyone, While trying to configure my network interface card on my system which runs mandrake 7, I have faced many problems. I used commands like netconf, drakconf, ifconfig etc to configure my NIC but of no use. There is no output for dmesg|grep eth. Does that mean that mandrake...

2. HP-UX

configuring nic card

using sam i have tryed to configure the nic, however when i try to do so i get an error saying i couldn't as i was using BIND ?

3. Linux

Howto Detect New Nic Card

Hi PPL! I have P-IV processor, with on-board NIC card. I have added one more NIC card for domestic use. My kudzu does not recognise the newly added PCMCIA NIC card. How to go about this one? Suggest PEnguin

4. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks

5. Solaris

Reg. NIC card

Hi friends i have problem with my home pc, i installed solaris 10 but my lan drivers are not installed, if i want to install drivers manually from where to download and how to install. I have Realtech lan card. when i type ifconfig -a it shows only localhost 127.0.0.0 Lo0 cannot see other than...

6. Solaris

NIC card repetative Failover

I have configure 2 NIC in ipmp group1 .Similarly other 2 NIC in ipmp group2 When I connect both NIC to 2 different switch , which is connect to one L3 switch as trunk. Both the NIC failover to each other continously. Following are the message log. ifmsdb1 in.mpathd: NIC failure detected...

7. Linux

How to check which NIC Card is used for backups?

I have a linux box with 2 nic cards on it one for prod and one for backup. My question is while the backup are happening how do I determine which nic is used for backups . I would like to run a command so that that I can see the usage in a dynamic fashion.

8. AIX

AIX -How to find which NIC is on which PCI card

Hi All, How can I find out which is ETH5 on my AIX P5 system. I have about seven different NIC card on this. I did move the cable to each one but still I was not able to see the link light up when I did netstat -v Any idea? Thanks.

9. HP-UX

NIC card issue

Hi, Someone asked me the below. If the box has multiple NIC cards, try to run a test with interface address specified as shown below $ java utils.MulticastTest -N server100 -A 237.155.155.1 -i <interfaceaddress> How can I now find out if my box has multiple NIC cards and how can I...

10. Red Hat

Finding speed of NIC Card

Hi, I would like to know how to find out ACTUAL speed of NIC Card. I have used the command ethtool eth0, it is showing supported modes, but what is acutal speed ? how to find out?

LEARN ABOUT SUSE

ocf_heartbeat_sendarp

OCF_HEARTBEAT_SENDAR(7) 					OCF resource agents					   OCF_HEARTBEAT_SENDAR(7)

NAME

       ocf_heartbeat_SendArp - Broadcasts unsolicited ARP announcements

SYNOPSIS

       SendArp [start | stop | monitor | meta-data | validate-all]

DESCRIPTION

       This script send out gratuitous Arp for an IP address

SUPPORTED PARAMETERS

       ip
	   The IP address for sending arp package. (required, string, no default)

       nic
	   The nic for sending arp package. (required, string, no default)

SUPPORTED ACTIONS

       This resource agent supports the following actions (operations):

       start
	   Starts the resource. Suggested minimum timeout: 20s.

       stop
	   Stops the resource. Suggested minimum timeout: 20s.

       monitor
	   Performs a detailed status check. Suggested minimum timeout: 20. Suggested interval: 10.

       meta-data
	   Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5.

       validate-all
	   Performs a validation of the resource configuration. Suggested minimum timeout: 20s.

EXAMPLE

       The following is an example configuration for a SendArp resource using the crm(8) shell:

	   primitive example_SendArp ocf:heartbeat:SendArp 
	     params 
	       ip=string 
	       nic=string 
	     op monitor depth="0" timeout="20" interval="10"

SEE ALSO

       http://www.linux-ha.org/wiki/SendArp_(resource_agent)

AUTHOR

       Linux-HA contributors (see the resource agent source for information about individual authors)

resource-agents 1.0.3						    07/05/2010						   OCF_HEARTBEAT_SENDAR(7)

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

No NIC Card?

Discussion started by: cyno

2. HP-UX

configuring nic card

Discussion started by: bobstar01

3. Linux

Howto Detect New Nic Card

Discussion started by: chakri.penguin

4. HP-UX

how can I determine which NIC card is virtual NIC Card

Discussion started by: alert0919