Sponsored Content
Full Discussion: interface may off
Operating Systems Solaris interface may off Post 302188099 by pupp on Tuesday 22nd of April 2008 03:55:56 PM
Old 04-22-2008
what do you get if you force a ping out bge3 to the default gwy? can you ping that gwy?
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. Solaris

no such interface

Hi Community, I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output: # ifconfig hme0 <ip_address> netmask <mask> plumb #ifconfig: plumb: hme0: no such interface I've the same thing with dhcp service. could you provide any solution... (1 Reply)
Discussion started by: Sunb3
1 Replies

3. IP Networking

How to down interface without name

Hi, ifconfig -a return: eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0 ... (5 Replies)
Discussion started by: djbuly
5 Replies

4. UNIX for Advanced & Expert Users

interface problem

hi all, i have problem with my box, until now i can't investigate the root cause of my issue at my box. here the problem. i have a box as a squid server just forward all request packet from one interface and receive the packet then forward to client at the same interface. but after 5 hours i... (1 Reply)
Discussion started by: tindasz
1 Replies

5. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

6. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you (2 Replies)
Discussion started by: TinhNhi
2 Replies

7. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ... (3 Replies)
Discussion started by: mghis
3 Replies

8. UNIX for Dummies Questions & Answers

Interface

Hi All, How to check whether a Interface has a single port or dual port.Thanks in advance. (5 Replies)
Discussion started by: rama krishna
5 Replies

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
OCF_PACEMAKER_PINGD(7)					      Pacemaker Configuration					    OCF_PACEMAKER_PINGD(7)

NAME
ocf_pacemaker_pingd - pingd resource agent SYNOPSIS
[OCF_RESKEY_pidfile=string] [OCF_RESKEY_user=string] [OCF_RESKEY_dampen=integer] [OCF_RESKEY_set=string] [OCF_RESKEY_name=string] [OCF_RESKEY_section=string] [OCF_RESKEY_multiplier=integer] [OCF_RESKEY_host_list=string] [OCF_RESKEY_interval=integer] [OCF_RESKEY_attempts=integer] [OCF_RESKEY_timeout=integer] [OCF_RESKEY_options=string] pingd [start | stop | monitor | meta-data | validate-all] DESCRIPTION
This agent (ocf:pacemaker:pingd) has been replaced by the more reliable ocf:pacemaker:ping. It records (in the CIB) the current number of ping nodes (specified in the 'host_list' parameter) a cluster node can connect to. SUPPORTED PARAMETERS
OCF_RESKEY_pidfile = string [/pingd-] PID file OCF_RESKEY_user = string [root] The user we want to run pingd as The user we want to run pingd as OCF_RESKEY_dampen = integer [5s] Dampening interval The time to wait (dampening) further changes occur OCF_RESKEY_set = string [] Set name The name of the instance_attributes set to place the value in. Rarely needs to be specified. OCF_RESKEY_name = string [pingd] Attribute name The name of the attributes to set. This is the name to be used in the constraints. OCF_RESKEY_section = string [] Section name The section place the value in. Rarely needs to be specified. OCF_RESKEY_multiplier = integer [] Value multiplier The number by which to multiply the number of connected ping nodes by OCF_RESKEY_host_list = string [] Host list The list of ping nodes to count. Defaults to all configured ping nodes. Rarely needs to be specified. OCF_RESKEY_interval = integer [1] ping interval in seconds How often, in seconds, to check for node liveliness OCF_RESKEY_attempts = integer [2] no. of ping attempts Number of ping attempts, per host, before declaring it dead OCF_RESKEY_timeout = integer [2] ping timeout in seconds How long, in seconds, to wait before declaring a ping lost OCF_RESKEY_options = string [] Extra Options A catch all for any other options that need to be passed to pingd. AUTHOR
Andrew Beekhof <andrew@beekhof.net> Author. Pacemaker Configuration 06/10/2014 OCF_PACEMAKER_PINGD(7)
All times are GMT -4. The time now is 08:40 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy