Visit The New, Modern Unix Linux Community

Operating Systems SCO PCI / PCIExpress Parallel port in SCO 6.0.0 Post 302186853 by uxlunatick on Friday 18th of April 2008 09:13:37 AM
With SCO 6.0.0 install, the teo PCIe gives errors during start-up. After MP3, 'hw' lists them as "simple communication" after. Does this tell me that the parallel ports are working?
 
Test Your Knowledge in Computers #485
Difficulty: Medium
A computer operating system loads an executable file into a call stack on a hard disk.
True or False?

9 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

Parallel Port info?

is there a command so that i can se info about the parallel port, if there isn't a specific command for that is there a command so i can se info about the system and all ports and devices? Thanx /Nick (2 Replies)
Discussion started by: sajjan2
2 Replies

2. Programming

parallel port proramming for sun ultra

Hi I'm trying to look for information about reading/writing to the parallel port of a Sun Ultra 5 running Solaris 8. I'd just like to see some basic programs written in C, nothing fancy, just reading and wrting to the port, getting the port address etc. toggling the lines. I've tried searching... (2 Replies)
Discussion started by: fishman2001
2 Replies

3. UNIX for Dummies Questions & Answers

SCO openserver 6 parallel port issues

I am having issues with SCO recognizing my parallel port. The port is being used so I can run dialogic using a dongle for the serial number but the port is not noticed. It is turned on in the bios and should work fine but when I attempt to run the software I get errno=6 and it appears to not be... (0 Replies)
Discussion started by: shuhemizer
0 Replies

4. UNIX for Advanced & Expert Users

SCO openserver 6 parallel port issues

I am having issues with SCO recognizing my parallel port. The port is being used so I can run dialogic using a dongle for the serial number but the port is not noticed. It is turned on in the bios and should work fine but when I attempt to run the software I get errno=6 and it appears to not be... (0 Replies)
Discussion started by: shuhemizer
0 Replies

5. SCO

PCI Express 1x HBA for parallel SCSI in Openserver 6

I'm floundering here trying to locate a PCI-E 1x HBA that will support an external tape drive in SCO Openserver 6. I was unable to find anything that would work in the compatible hardware list and a call to Adaptec confirmed that PCI-X would've been a better option for the risers in the Dell 2950... (1 Reply)
Discussion started by: s_mal
1 Replies

6. UNIX for Dummies Questions & Answers

Parallel port Printing in SCO OSR6

Hi, I am trying to add a parallel printer to my SCO OSR6 server, yet when I run mkdev parallel it just brings up the message: "Parallel Ports are configured automatically in SCO Openserver 6". So when I try and add a local printer, no /dev/lp# ports are shown in the list, only serial ports... (1 Reply)
Discussion started by: Martyn
1 Replies

7. Fedora

Sending a byte to the parallel port

Greetings, A sort of newbie question... I would like to control a couple of stepper motors via the parallel port using C code. I have discovered in Linux, the ioperm() function is required before the outportb() function can be used to send a byte to the parallel port. My problem is ioperm()... (1 Reply)
Discussion started by: meyerga00
1 Replies

8. AIX

NPIV with 8Gb PCI Express Dual Port FC Adapter

All I am at a loss with a VIO server running ios 2.2.0.10-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable: $ lsnports name physloc ... (4 Replies)
Discussion started by: johnf
4 Replies

9. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies
PCCBB(4)						   BSD Kernel Interfaces Manual 						  PCCBB(4)

NAME
pccbb -- cardbus bridge driver SYNOPSIS
device cbb device pccard device cardbus device exca DESCRIPTION
The pccbb driver implements the Yenta specification for CardBus bridges. The following PCI cardbus and pcmcia bridges are supported: Cirrus Logic PD6832 Cirrus Logic PD6833 Cirrus Logic PD6834 O2micro OZ6812 O2micro OZ6832 O2micro OZ6833 O2micro OZ6836 O2micro OZ6860 O2micro OZ6872 O2micro OZ6912 O2micro OZ6922 O2micro OZ6933 O2micro OZ6972 O2Micro OZ711E1 O2Micro OZ711M1 Ricoh RL4C475 Ricoh RL4C476 Ricoh RL4C477 Ricoh RL4C478 TI PCI-1031 TI PCI-1130 TI PCI-1131 TI PCI-1210 TI PCI-1211 TI PCI-1220 TI PCI-1221 TI PCI-1225 TI PCI-1250 TI PCI-1251 TI PCI-1251B TI PCI-1260 TI PCI-1260B TI PCI-1410 TI PCI-1420 TI PCI-1450 TI PCI-1451 TI PCI-1510 TI PCI-1515 TI PCI-1520 TI PCI-1530 TI PCI-1620 TI PCI-4410 TI PCI-4450 TI PCI-4451 TI PCI-4510 TI PCI-4520 TI PCI-[67]x[12]1 TI PCI-[67]x20 ENE CB710 ENE CB720 ENE CB1211 ENE CB1255 ENE CB1410 ENE CB1420 Toshiba ToPIC95 Toshiba ToPIC95B Toshiba ToPIC97 Toshiba ToPIC100 TUNABLES
The driver supports the following tunable parameters, which may be added to /boot/loader.conf or set via the sysctl(8) command: hw.cbb.debug Non-zero values cause more verbose information to be printed to aid in debugging problems with the bridge chipset. SEE ALSO
cardbus(4), pccard(4), exca(4) BSD
July 21, 2004 BSD

Featured Tech Videos

All times are GMT -4. The time now is 01:41 AM.
Unix & Linux Forums Content Copyright 1993-2020. All Rights Reserved.
Privacy Policy