Hey all,
I have a box running SUSE SLES 8 and in the past few months the box will randomly spawn thousands of instances of /USR/SBIN/CRON to the point where the box will lock up entirely. Upwards of 14000 instances! I imagine it's using up all of the available files that can be opened at one... (10 Replies)
Hi All,
I want to find a specific pattern from approximately 400000 files on solaris platform. Its very heavy for me to grep that pattern to each file individually.
Can anybody suggest me some way to search for specific pattern (alpha numeric) from these forty thousand files. Please note that... (6 Replies)
Hi experts,
I have thousands of file (data file and Gziped file) in same directory like below--
bash-2.05$ pwd
/home/mmc
bash-2.05$ file PP023149200709270546
TT023149200709270546: gzip compressed data - deflate method
bash-2.05$ file PP027443200711242320
TT027443200711242320: ... (10 Replies)
There is a procedure I do here at work where I have to synchronize file systems. The source file system always has three or four directories of hundreds of thousands of tiny (1k or smaller) or empty files. Whenever my rsync command reaches these directories, I'm waiting for hours for those files... (3 Replies)
Folder of e-mails in maildir format had been corrupted. Typical file name is 1246281161.6777.m21JH:2,S . The " :2,S prevents " copying to another device. How can I simply remove the last four characters? (2 Replies)
I need to find a smarter way to process about 60,000 files in a single directory.
Every night a script runs on each file generating a output on another directory; this used to take 5 hours, but as the data grows it is taking 7 hours.
The files are of different sizes, but there are 16 cores... (10 Replies)
Hi All,
I want to search for a certain string in thousands of files and these files are distributed over different directories created daily. For that I created a small script in bash but while running it I am getting the below error:
/ms.sh: xrealloc: subst.c:5173: cannot allocate... (17 Replies)
Hi to all,
I have thousand of files in a folder with names with format "FILE-YYYY-MM-DD-HHMM" for what I want to send the following AWK command
awk '/Code.*/' FILE-2014*
I'd like to separate all files that have the same date to a folder named with the corresponding date. For example, if I... (7 Replies)
Discussion started by: Ophiuchus
7 Replies
LEARN ABOUT SUSE
ifsysctl
IFSYSCTL(5) Network configuration IFSYSCTL(5)NAME
ifsysctl[-<interface name>] - per network interface sysctl settings
SYNOPSIS
/etc/sysconfig/network/ifsysctl
/etc/sysconfig/network/ifsysctl-<interface name>
DESCRIPTION
These files are intended to contain sysctl settings, that should be applied when a network interface is created. This are usually interface
specific settings, like:
net.ipv6.conf.eth0.use_tempaddr = 1
or
net.ipv4.conf.eth0.rp_filter = 0
The settings are applied by the /etc/sysconfig/network/scripts/ifup-sysctl script executed via /etc/udev/rules.d/77-network.rules rule (see
udev(7)), after the creation and after the rename of the interface name to its persistent name (when applicable), but before the ifup
<interface name> -o hotplug may be executed to configure the interface.
The settings are not applied by default when the NetworkManager is active (NETWORKMANAGER=yes), except when the IFSYSCTL_NETWORKMANAGER=yes
variable is set in the /etc/sysconfig/network/config file.
Settings from the ifsysctl- file are applied every time an interface has been created.
Settings from the ifsysctl-interface name file are applied when the interface with the corresponding interface name has been created.
SYNTAX
The sysctl(8) utility is required to apply the settings. It supports two separator characters for sysctl keywords: a "." in default format
and a "/" in the alternate format. Therefore the syntax is basically same to the /etc/sysctl.conf file.
Interface names may contain a ".". In the default sysctl format using a "." as separator, that is any "." in the interface name of the key-
word, has to be replaced with a "/". In the alternate sysctl format with "/" as separator, normal interface names can be used.
Optionally, the ifsysctl files may contain also the $INTERFACE and the $SYSCTL_IF variables, that are automatically replaced with the cur-
rent interface name usable in the alternate format and with the sysctl-quoted interface name for the default format, before the settings
are passed to the sysctl utility.
Note also, that settings with variables in the ifsysctl (without the -<interface name> suffix), will be applied for every interface!
Further, files with variables are not compatible to the /etc/sysctl.conf file.
EXAMPLES
Settings for "eth0" and "eth0.1" interfaces
# using "." as separator:
net.ipv6.conf.eth0.use_tempaddr = 1
net.ipv6.conf.eth0/1.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/eth0/use_tempaddr = 1
net/ipv6/conf/eth0.0/use_tempaddr = 1
Settings with variables:
# using "." as separator:
net.ipv6.conf.$SYSCTL_IF.use_tempaddr = 1
# using "/" as separator:
net/ipv6/conf/$INTERFACE/use_tempaddr = 1
To test your ifsysctl-eth0 or ifsysctl file, use:
/etc/sysconfig/network/scripts/ifup-sysctl eth0 -o debug
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO ifup(8)ifcfg(5)sysctl(8)sysconfig December 2009 IFSYSCTL(5)