04-02-2008
SuSe Linux Mount
Hi everyone, I am new to Linux and I hope to have some advise.
Suppose I have 2 differnt users who require differnt mount drives. When user1 logs in, his required drives are mounted. When user2 logs in, user1's drives are unmounted and user2's drives are mounted.
May I know how I can achieve this? Many thanks in advance.
4 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
We are experiencing several startup problems at boot time. In our
/etc/rc.d/boot script we have "swapon -a -v &> /dev/null/' (without the
quotes). We have also added echo statements to make it visible on the
HMC during IPL. The echo statements are seen but there no messages for
the swapon... (1 Reply)
Discussion started by: darthur
1 Replies
2. UNIX for Dummies Questions & Answers
I have installed SUSE 10 on a laptop that has a swappable CDROM/Floppy drive. When I was installing the OS my CDROM was connected. Later I tried to swap it with the Floppy and mount it but no success. Here is what I get:
dell:/dev # mount -t msdos /dev/fd0 /mnt
/dev/fd0: Invalid argument
... (0 Replies)
Discussion started by: reedcat
0 Replies
3. OS X (Apple)
as the title states, i cant mount suse of apple volumes on either box. have tryed afpfs-ng but no love.
anyone have a suggestion than samba (because i dislike MS) and NFS because i don't know jack about it..... yet
thanks in advance
julz (4 Replies)
Discussion started by: biorhythm
4 Replies
4. Linux
i'm new linux ... after reboot ...... my keyboard is notworking
automatically boot ..... after few mins
Waiting for mandatory devices: eth-id-00:10:a7:08:cb:4b
12 11 9 8 7 5 4 3 1 0
eth0 interface could not be set up
failed
Setting up service network . . . . . . . . . . . . .
... (2 Replies)
Discussion started by: coolboys
2 Replies
IDA(4) BSD Kernel Interfaces Manual IDA(4)
NAME
ida -- Compaq Intelligent Drive Array Controllers
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device ida
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ida_load="YES"
DESCRIPTION
The Compaq Intelligent Drive Array (IDA) technology is used to distribute data across an array of hard drives. It unites these hard drives
into one or more high-performance logical drives. The drive array is managed by an array controller.
These controllers have the ability to provide fault tolerance for the connected drives and optionally provide write cache for the logical
drives. It is also possible for an application to access the SCSI bus subsystem directly by using the pass-through interface.
HARDWARE
The following controllers are supported by the ida driver:
o Compaq SMART Array 221
o Compaq Integrated SMART Array Controller
o Compaq SMART Array 4200
o Compaq SMART Array 4250ES
o Compaq SMART 3200 Controller
o Compaq SMART 3100ES Controller
o Compaq SMART-2/DH Controller
o Compaq SMART-2/SL Controller
o Compaq SMART-2/P Controller
o Compaq SMART-2/E Controller
o Compaq SMART Controller
IMPLEMENTATION NOTES
Extreme caution should be exercised when using the pass-through interface. It is possible to interfere with normal system I/O and cause
hangs if pass-through is used to an active device. Pass-through should only be used to a device that is otherwise quiescent.
SEE ALSO
cam(4), pass(4), xpt(4), camcontrol(8)
AUTHORS
The ida driver was written by Jonathan Lemon <jlemon@FreeBSD.org> and Matthew N. Dodd <mdodd@FreeBSD.org>. This manual page was written by
Tom Rhodes <trhodes@FreeBSD.org>.
BSD
August 8, 2004 BSD