03-29-2008
Only LAN access after fresh install
Hello,
For whatever reason, after installing Solaris 10 I can ping anything within my own LAN, including the router which is also set as the default gateway, but I have no internet connectivity with it. At first I thought this was a DNS issue, but I can't connect with external IP addresses either. If it matters, this server is being run in VMware Workstation 6, and I have had a similar server working properly before with the same hardware configuration. The only thing I can think of is that I gave this server a hostname, and it seems to think that it's part of a domain although it's just a windows workgroup.
Any suggestions?
edit:
Another issue I have is that the filesystem is much smaller than the total space I allocated to the virtual HD (I allocated all space before installing the OS, 8 GBs). It's only an issue because I'm trying to set up a Lotus Domino mailing server, and I only have exactly 1 GB of free space allocated to the file system. How do I partition the rest of the hard drive so it can be used in this way?
10 More Discussions You Might Find Interesting
1. HP-UX
I've just completed a fresh install of HP-UX 11.0 on my 712/80 and everything starts up fine until it gets to the point where X kicks off and I believe at this point is supposed to launch into the CDE login.
It just sits there on the blank X screen with the X cursor for a minute or so then BEEPS... (9 Replies)
Discussion started by: ErikTheHAck
9 Replies
2. AIX
I've installed AIX 5.1 on a 43p-140, but am unable to log in. At no point in the install did it ask me for a root password. When it boots to the console prompt, I enter "root" as a username, and then after 1 second it cycles right back to another root prompt.
I am accessing the 43p-140... (4 Replies)
Discussion started by: akbar
4 Replies
3. Solaris
Dear
i have installed Solaris 10 on SUN V240
after installation i can not access system through root user
if i access system through any other user it conects but root is not connecting through LAN
if i connect through SC and then access root though cosole -f command it also works
kindly... (6 Replies)
Discussion started by: rizwan225
6 Replies
4. Web Development
I have installed WAMPSERVER 2.0 on my windows vista x64 system but still am having issues with getting the webserver to be seen outside my local network. It is working fine within my local network.
Been through several setup tutorials so far, no dice still.
For testing purposes I have... (1 Reply)
Discussion started by: davidmanvell
1 Replies
5. Solaris
Hi all
Im rebuilding an 6800 domain with solaris 10. Server is located in a different town and cant be bothered to drive down and install a dvd into its drive.
So, apart from jumpstarting it and using a local DVD, is there a way I can an ISO image to build a new client ?? eg. mount an ISO... (2 Replies)
Discussion started by: sbk1972
2 Replies
6. Solaris
Installing Solaris 8 for the first time...on a SunBlade 100. I have original Solaris 8 CD's.
About 45 minutes into the installation, the install halts with the following errors:
ERROR: Could not open file /a/etc/vfstab
ERROR: Could not create the file system mount table /etc/vfstab
I... (4 Replies)
Discussion started by: cdunavent
4 Replies
7. UNIX for Dummies Questions & Answers
DELETE (0 Replies)
Discussion started by: morrison71
0 Replies
8. AIX
Hi Everyone,
I have been struggling for few days with iSCSI and thought I could get some help on the forum...
fresh install of AIX7.1 TL4 on Power 710, The rootvg relies on 3 SAS disks in RAID 0, 32GB Memory
The lpar Profile is using all of the managed system's resources.
I have connected... (11 Replies)
Discussion started by: frenchy59
11 Replies
9. Debian
Hello,
I have downloaded and install debian in computer it is blinking cursor what this mean? (6 Replies)
Discussion started by: Riteshkakkar
6 Replies
10. Solaris
I have M10-1. Installation OS 10 from cdrom external.
Here message from OK Prompt
{0} ok probe-scsi-all
/pci@8000/pci@4/pci@0/pci@2/pci@0/usb@4,1/cdrom@1
Unit 0 Removable Read Only device HL-DT-STDVDRAM GP65NB60 PF00
But..
{0} ok boot... (3 Replies)
Discussion started by: mbahjiman
3 Replies
LEARN ABOUT FREEBSD
if_vmx
VMX(4) BSD Kernel Interfaces Manual VMX(4)
NAME
vmx -- VMware VMXNET3 Virtual Interface Controller device
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device vmx
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_vmx_load="YES"
DESCRIPTION
The vmx driver provides support for the VMXNET3 virtual NIC available in virtual machines by VMware. It appears as a simple Ethernet device
but is actually a virtual network interface to the underlying host operating system.
This driver supports the VMXNET3 driver protocol, as an alternative to the emulated pcn(4), em(4) interfaces also available in the VMware
environment. The vmx driver is optimized for the virtual machine, it can provide advanced capabilities depending on the underlying host
operating system and the physical network interface controller of the host. The vmx driver supports features like multiqueue support, IPv6
checksum offloading, MSI/MSI-X support and hardware VLAN tagging in VMware's VLAN Guest Tagging (VGT) mode.
The vmx driver supports VMXNET3 VMware virtual NICs provided by the virtual machine hardware version 7 or newer, as provided by the following
products:
o VMware ESX/ESXi 4.0 and newer
o VMware Server 2.0 and newer
o VMware Workstation 6.5 and newer
o VMware Fusion 2.0 and newer
For more information on configuring this device, see ifconfig(8).
MULTIPLE QUEUES
The vmx driver supports multiple transmit and receive queues. Multiple queues are only supported by certain VMware products, such as ESXi.
The number of queues allocated depends on the presence of MSI-X, the number of configured CPUs, and the tunables listed below. FreeBSD does
not enable MSI-X support on VMware by default. The hw.pci.honor_msi_blacklist tunable must be disabled to enable MSI-X support.
LOADER TUNABLES
Tunables can be set at the loader(8) prompt before booting the kernel or stored in loader.conf(5).
hw.vmx.txnqueue
hw.vmx.X.txnqueue
Maximum number of transmit queues allocated by default by the driver. The default value is 8. The maximum supported by the VMXNET3
virtual NIC is 8.
hw.vmx.rxnqueue
hw.vmx.X.rxnqueue
Maximum number of receive queues allocated by default by the driver. The default value is 8. The maximum supported by the VMXNET3
virtual NIC is 16.
hw.vmx.txndesc
hw.vmx.X.txndesc
Number of transmit descriptors allocated by the driver. The default value is 512. The value must be a multiple of 32, and the maxi-
mum is 4096.
hw.vmx.rxndesc
hw.vmx.X.rxndesc
Number of receive descriptors per ring allocated by the driver. The default value is 256. The value must be a multiple of 32, and
the maximum is 2048. There are two rings so the actual usage is doubled.
EXAMPLES
The following entry must be added to the VMware configuration file to provide the vmx device:
ethernet0.virtualDev = "vmxnet3"
SEE ALSO
altq(4), arp(4), em(4), netintro(4), ng_ether(4), pcn(4), vlan(4), ifconfig(8)
AUTHORS
The vmx driver was ported from OpenBSD and significantly rewritten by Bryan Venteicher <bryanv@freebsd.org>. The OpenBSD driver was written
by Tsubai Masanari.
BSD
March 17, 2014 BSD