Sponsored Content
Operating Systems Solaris Only LAN access after fresh install Post 302180116 by Quadratic on Saturday 29th of March 2008 09:07:11 PM
Old 03-29-2008
Only LAN access after fresh install

Hello,

For whatever reason, after installing Solaris 10 I can ping anything within my own LAN, including the router which is also set as the default gateway, but I have no internet connectivity with it. At first I thought this was a DNS issue, but I can't connect with external IP addresses either. If it matters, this server is being run in VMware Workstation 6, and I have had a similar server working properly before with the same hardware configuration. The only thing I can think of is that I gave this server a hostname, and it seems to think that it's part of a domain although it's just a windows workgroup.

Any suggestions?

edit:

Another issue I have is that the filesystem is much smaller than the total space I allocated to the virtual HD (I allocated all space before installing the OS, 8 GBs). It's only an issue because I'm trying to set up a Lotus Domino mailing server, and I only have exactly 1 GB of free space allocated to the file system. How do I partition the rest of the hard drive so it can be used in this way?
 

10 More Discussions You Might Find Interesting

1. HP-UX

11.0 fresh install: I never see CDE Login

I've just completed a fresh install of HP-UX 11.0 on my 712/80 and everything starts up fine until it gets to the point where X kicks off and I believe at this point is supposed to launch into the CDE login. It just sits there on the blank X screen with the X cursor for a minute or so then BEEPS... (9 Replies)
Discussion started by: ErikTheHAck
9 Replies

2. AIX

Root password for fresh 5.1 install on 43p-140?

I've installed AIX 5.1 on a 43p-140, but am unable to log in. At no point in the install did it ask me for a root password. When it boots to the console prompt, I enter "root" as a username, and then after 1 second it cycles right back to another root prompt. I am accessing the 43p-140... (4 Replies)
Discussion started by: akbar
4 Replies

3. Solaris

I can not access root user through LAN

Dear i have installed Solaris 10 on SUN V240 after installation i can not access system through root user if i access system through any other user it conects but root is not connecting through LAN if i connect through SC and then access root though cosole -f command it also works kindly... (6 Replies)
Discussion started by: rizwan225
6 Replies

4. Web Development

Cannot access Apache web server from Wan side, only Lan side.

I have installed WAMPSERVER 2.0 on my windows vista x64 system but still am having issues with getting the webserver to be seen outside my local network. It is working fine within my local network. Been through several setup tutorials so far, no dice still. For testing purposes I have... (1 Reply)
Discussion started by: davidmanvell
1 Replies

5. Solaris

Fresh install of solaris 10 using an ISO

Hi all Im rebuilding an 6800 domain with solaris 10. Server is located in a different town and cant be bothered to drive down and install a dvd into its drive. So, apart from jumpstarting it and using a local DVD, is there a way I can an ISO image to build a new client ?? eg. mount an ISO... (2 Replies)
Discussion started by: sbk1972
2 Replies

6. Solaris

Solaris 8 fresh install halts

Installing Solaris 8 for the first time...on a SunBlade 100. I have original Solaris 8 CD's. About 45 minutes into the installation, the install halts with the following errors: ERROR: Could not open file /a/etc/vfstab ERROR: Could not create the file system mount table /etc/vfstab I... (4 Replies)
Discussion started by: cdunavent
4 Replies

7. UNIX for Dummies Questions & Answers

KVM: can't access VM from another computer in same LAN.

DELETE (0 Replies)
Discussion started by: morrison71
0 Replies

8. AIX

ISCSI poor performance 1.5MB/s fresh install AIX7.1

Hi Everyone, I have been struggling for few days with iSCSI and thought I could get some help on the forum... fresh install of AIX7.1 TL4 on Power 710, The rootvg relies on 3 SAS disks in RAID 0, 32GB Memory The lpar Profile is using all of the managed system's resources. I have connected... (11 Replies)
Discussion started by: frenchy59
11 Replies

9. Debian

Debian fresh install blinking cursor meaning?

Hello, I have downloaded and install debian in computer it is blinking cursor what this mean? (6 Replies)
Discussion started by: Riteshkakkar
6 Replies

10. Solaris

Fresh Install - Boot Load Failed

I have M10-1. Installation OS 10 from cdrom external. Here message from OK Prompt {0} ok probe-scsi-all /pci@8000/pci@4/pci@0/pci@2/pci@0/usb@4,1/cdrom@1 Unit 0 Removable Read Only device HL-DT-STDVDRAM GP65NB60 PF00 But.. {0} ok boot... (3 Replies)
Discussion started by: mbahjiman
3 Replies
namepool(4)						     Kernel Interfaces Manual						       namepool(4)

NAME
namepool - DHCP server database DESCRIPTION
The namepool database provides joind with names that are available for dynamic assignment to clients of the DHCP protocol. For each DHCP server and domain name (NIS or DNS), the database contains a collection of names available for allocation to DHCP clients within those domains. One name plays a distinguished role - it is used as a prefix when the pool has been exhausted. Names are generated from the pre- fix by appending a number, 1,2.., and a trailing 'd'. The namepool file is read whenever joind starts. Names within the database must not be allocated to hosts which are not DHCP clients, and if the administration of a domain is shared between several DHCP servers, the name- pools that each has must be disjoint. Names may be added and removed from the namepool file. If a name is removed from the file it remains bound to the client to which it was allocated; if no such binding is in effect the name is excised from the server's pool the next time the server starts. Once a name is dynamically bound to a host it will never be reused even if that host subsequently acquires a new name, but there is no need to remove it from namepool. FORMAT Blank lines and lines beginning with a number sign (#) are ignored. A new entry must begin in column one and has one of the following for- mats: domain server domain server name_prefix The domain variable is the domain in which the names which follow are assigned. The server variable is the name or IP address of the server in charge of allocating these names to clients. The prefix variable is the prefix that will be used when the pool is exhausted. Succeeding lines contain one or more names for domains that are to be allocated by the server. Each of these succeeding lines must begin with at least one white space character. FILES
/etc/join/namepool RELATED INFORMATION
joind(8), join.ipaddresses(4) delim off namepool(4)
All times are GMT -4. The time now is 03:55 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy