I need to replace the line containing "STAGE_DB" with the line
"STAGE_DB $DB # database that contains the table being loaded ($workingDB)"
Here $DB is passed during the runtime.
How can I do this?
Thanks,
Kousikan (2 Replies)
Hi all,
I've been working on a script which I have hit a road block now. I have written a script using sed to extract the below data and pumped into another file:
Severity............: MAJORWARNING
Summary:
System temperature is out of normal range.
Severity............: MAJORWARNING... (13 Replies)
Hi
I'm not very good with the serach patterns and I'd need a sample how to find a line that has multiple patterns.
Say I want to find a line that has "abd", "123" and "QWERTY" and there can be any characters or numbers between the serach patterns, I have a file that has thousands of lines and... (10 Replies)
I am searching a dhcpd.conf to find the hardware ethernet match, then once the match is found delete just the line above it. For example:
testmachine.example {
hardware ethernet 00:00:00:00:00:00;
fixed address 192.168.1.100;
next-server 192.168.1.101;
filename "linux-install/pxelinux.0";
}... (3 Replies)
the following range matching works great but i wish to add a blank line after each range result set... which i've tried and researched to no avail
MY INPUT DATA:
CURRENT CODE I'M USING:
sed -n '/*$/,/;/p' $INPUT_FILE
RESULTS I'M GETTING:
RESULT I looking to... (5 Replies)
Hello,
I want to do a simple substitution using sed but I can't find a solution. Basically, from a Apache conf file, I would like to remove everything included between the <VirtualHost> and </VirtualHost> e.g
SSLMutex file:/var/run/ssl_mutex
<VirtualHost _default_:443>
# A lot of config that... (5 Replies)
Hi,
I want to match a line which exists in a file. I have written a test script similar to below -
The content of the file file.txt would be like this -
/usr/bin/1234.xcf
/usr/bin/3456.xcf
/usr/bin/7897.xcf
/usr/bin/2345.xcf
out=`sed -n '\/usr\/bin\/7897.xcf/p' file.txt 2>&1`... (3 Replies)
Dear all,
I need to search multiple patterns and then I need to print their respective next lines. For an example, in the below table, I will look for 3 different patterns :
1) # ATC_Codes:
2) # Generic_Name:
3) # Drug_Target_1_Gene_Name:
#BEGIN_DRUGCARD DB00001
# AHFS_Codes:... (3 Replies)
Hi How Are you?
I am doing fine!
I need to go now?
I will see you tomorrow!
Basically I need to replace the entire line containing "doing" with a blank line:
I need to the following output:
Hi How Are you?
I need to go now?
I will see you tomorrow!
Thanks in advance.... (1 Reply)
I need to match two patterns in a log file and need to get the next line of the one of the pattern (out of two patterns) that is matched,
finally need to print these three values in a single line.
Sample Log:
2013/06/11 14:29:04 <0999> (725102) Processing batch 02_1231324
2013/06/11... (4 Replies)
Discussion started by: rpm120
4 Replies
LEARN ABOUT DEBIAN
irsend
IRSEND(1) User Commands IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.9.0-pre1 October 2010 IRSEND(1)