03-25-2008
8 More Discussions You Might Find Interesting
1. IP Networking
Hello guyz..
did some of u have implement or making a testbed for IPv6?
if yes, can u attached the procedures and standard guidelines because i really need for my proposal..
thanx.. (2 Replies)
Discussion started by: unknown2205
2 Replies
2. SuSE
Hi gurus,
In a few month, we must enable IPv6 on our Linux Server!
Should we reinstall the Linux machine to enable IPv6 or could we just make some change in configuration's files?
Could Linux run simultaneous IPv4 and IPv6?
Thanks in advance for our help our ideas?
Best regards,
nm (3 Replies)
Discussion started by: hiddenshadow
3 Replies
3. Solaris
I am currently trying to setup static ipv6 address with a persistent default gateway. This is on a Solaris 10 non global zone running inside a Solaris 10 global zone. My production server I am comparing against is a Solaris 10 xen instance running on a Oracle Solaris xen instance.
I have got... (12 Replies)
Discussion started by: jpolachak
12 Replies
4. Red Hat
In our server routing ipv6 auth config IP and IPv6 routing got flushed out automatically.
Can some one help what could be the cause (0 Replies)
Discussion started by: dpmoorthy
0 Replies
5. HP-UX
my problem: i want to change from ipv4 to ipv6 on my home network.
On hpux i can assign only address non routable as fe80::1 fe80::3 etc to my lan0
Editing netconf-ipv6 i can assing a routable ipv6 address like
fd55:282f:3b98::/48
or
2001:470:26:307:89a0:aba1:f98b:eb3e
but only to alias... (0 Replies)
Discussion started by: Linusolaradm1
0 Replies
6. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
7. IP Networking
I am trying to setup an IPv6 network.
I modified the interfaces file:
/etc/network/interfaces
# The loopback network interface
auto lo
iface lo inet loopback
iface etho0 inet static
address 2620:7:a000::1
netmask 64
gateway ::ffff:c0a8:101
... (0 Replies)
Discussion started by: Meow613
0 Replies
8. Solaris
Hello Dears ,
please I need your support I have Oracle Solaris 10 X86 server please if you can advise how can I add IP v6 on my server and if IPv6 was disabled how can i enable it also how can i add two IP (v4 and v6) on the same interface or I have to add another interface .
Thanks in... (1 Reply)
Discussion started by: ttashman
1 Replies
LEARN ABOUT OSX
httppower
httppower(8) powerman httppower(8)
NAME
httppower - communicate with HTTP based power distribution units
SYNOPSIS
httppower [--url URL]
DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac-
tively by the powerman daemon.
OPTIONS
-u, --url URL
Set the base URL.
INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt:
auth user:pass
Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
over the network in plain text.
seturl URL
Set the base URL. Overrides the command line option.
get [URL-suffix]
Send an HTTP GET to the base URL with the optional URL-suffix appended.
post [URL-suffix] key=val[&key=val]...
Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.
FILES
/usr/sbin/httppower
/etc/powerman/powerman.conf
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 httppower(8)