|
|
Sponsored Content
Operating Systems
Linux
DHCP setup
Post 302177871 by sad_angle on Sunday 23rd of March 2008 11:40:50 PM
03-24-2008
|
|
10 More Discussions You Might Find Interesting
1. IP Networking
Hello all, I have this Intel Pentium 233/128 running Solaris 8. I also have a dhcp/router/dns running SuSElinux 7.2.(Sorry if it is out of topic here) My problem is that the Solaris box when it tries to configure the interface (elxl0) via dhcp it fails. It appears, according to the... (1 Reply)
Discussion started by: jdevarie
1 Replies
2. UNIX for Advanced & Expert Users
Hi you all. I'm trying to enable DHCP in a Sun Utra 5 runing Solaris 8 but during the boot process it sends me the message : "Device not in appropiate status"
Do anyone have enabled DHCP on solaris 8?
Any Procedure?
The DHCP server is an NT I guess. (2 Replies)
Discussion started by: alex blanco
2 Replies
3. UNIX for Dummies Questions & Answers
HI,
New to Unix and I inherited a network that runs DHCP in manual configuration mode. Basically, in order for a machine to get an IP it has to have an entry in dhcpd.conf with its MAC address mapped to a hostname (the hostname then maps to an IP address listed in the DNS db file). If there is... (2 Replies)
Discussion started by: NJay
2 Replies
4. AIX
I know that IBM's official stance is that NIM does not work on etherchannel environment, but has anyone able to get around it?
I'm working on a p5-590 LPAR system, and the NIM master and clients are all on the same frame.
Any help is appreciated. (1 Reply)
Discussion started by: pdtak
1 Replies
5. IP Networking
hi
i have been given task to setup a small network with dhcp on linux. i have tried few tricks but i get an error massage stating that dhcpd failed to start. More troubles followers
dhcpd.service - DHCPv4 Server Daemon
Loaded: loaded (/lib/systemd/system/dhcpd.service)
Active:... (1 Reply)
Discussion started by: mduduzi
1 Replies
6. UNIX for Advanced & Expert Users
Is dnsmasq important for dhcp to setup dns? (3 Replies)
Discussion started by: cokedude
3 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
I am trying to configure dhcp server on a linux host with eth0:1 which is using 192.168.1.10
I also want to restrict my DHCP client to just one Host adcnew222.
DHCP Server Host name - adcnew111
DHCP client name - adcnew222
My conf file is as follows on dhcp server :
... (2 Replies)
Discussion started by: sriram003
2 Replies
8. IP Networking
Dear Experts,
I have a TI DM8148 EVM board REV C, the EZSDK5.05 SW package, and DVRRDK1.09 SW package.
EZSDK5.05, DVRRDK1.09 both use Linux2.6.37, however, there are some modifications between these two kernels.
When I use uImage of DVRRDK1.09 to boot up EVM board, this board can be given a... (0 Replies)
Discussion started by: oobin168
0 Replies
9. IP Networking
Hi All ,
please view the set up below:
-------------------------------------------------------------------
| DHCP Server |-----------| ROUTER & |-----------| Clients |
| 192.168.99.1 | - -<eth1>| DHCP-RELAY|<eth2>-- | 192.168.88.X |
... (2 Replies)
Discussion started by: gdangoor
2 Replies
10. IP Networking
I have a DHCP thing on my HP printer. How can I find information on numbers for that? (2 Replies)
Discussion started by: teak
2 Replies
LEARN ABOUT OPENSOLARIS
optisa
optisa(1) User Commands optisa(1) NAME
optisa - determine which variant instruction set is optimal to use SYNOPSIS
optisa instruction_set... DESCRIPTION
optisa prints which instruction_set out of the ones specified in the command will perform best on this machine. In this case, ``best'' is defined by the order in which instruction set names are returned by isalist(1). Possible values for instruction_set are given in isalist(5). ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ EXIT STATUS
The following exit values are returned: 0 One of the instruction_set values you specified is printed by this command. 1 There is no output; that is, this machine cannot use any instruction_set that you specified with the optisa command. SEE ALSO
isalist(1), uname(1), attributes(5), isalist(5) NOTES
optisa is preferable to uname -p or uname -m (see uname(1)) in determining which of several binary versions of a given program should be used on the given machine. SunOS 5.11 25 Jul 1997 optisa(1)