03-19-2008
Problems using rsh
Hi,
I have a server which I've configured to allow an rsh trust from a csm server. However, of the 3 vlans on the target server, I can only rsh to one of them without being prompted for the password.
On lpar1
$ ifconfig -a
en2: flags=1e080863,480<UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST,GROUPRT,64BIT,CHECKSUM_OFFLOAD( ACTIVE),CHAIN>
inet 10.162.73.138 netmask 0xffffff80 broadcast 10.162.73.255
tcp_sendspace 262144 tcp_recvspace 262144 rfc1323 1
en3: flags=5e080863,c0<UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST,GROUPRT,64BIT,CHECKSUM_OFFLOAD(A CTIVE),PSEG,LARGESEND,CHAIN>
inet 10.162.70.71 netmask 0xffffffc0 broadcast 10.162.70.127
en5: flags=1e080863,80<UP,BROADCAST,NOTRAILERS,RUNNING,SIMPLEX,MULTICAST,GROUPRT,64BIT,CHECKSUM_OFFLOAD(A CTIVE),CHAIN>
inet 10.162.73.11 netmask 0xffffff80 broadcast 10.162.73.127
tcp_sendspace 262144 tcp_recvspace 262144 rfc1323 1
On csm server
csms01:/ $ rsh 10.162.70.71
root's Password:
csms01:/ $ rsh 10.162.73.11
root's Password:
csms01:/ $ rsh 10.162.73.138
Last login: Wed Mar 19 12:51:07 GMT 2008 on /dev/pts/0 from csms01-tsm
root@lpar1:/ $
Can anyone suggest why this only works to 1 of the vlans? I have several other servers with a similar ip configuration and I can rsh too all the vlans without any problems.
Thanks
Gareth
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hello Everybody,
I have a set of four machines. When i try to rsh between them i get errors like 'no route to host' and 'conection refused'. What do i need to do to rectify this problem..... i can ssh between the nodes ok but only if i supply a password.
Here is the output from my screen:
... (1 Reply)
Discussion started by: rkap
1 Replies
2. UNIX for Dummies Questions & Answers
I am using rsh and other R commands to login to a machine.
On that target machine, I set up $HOME/.rhosts file with the host/password.
I also setup /etc/hosts.equiv fiel with IP address/username.
I also made sure that rsh was enabled and that no firewall was running.
The /etc/hosts on... (7 Replies)
Discussion started by: etc
7 Replies
3. UNIX for Advanced & Expert Users
Hi,
on .rhosts file of server2 I have :
server1 user
server1 root
when I want to issu rsh from server1 to server2 :
1-If I'm root it is OK.
2-if I'm ordinary user I receive permission denied.
What is the problem ? What is the solution ?
Many thanks in advance. (4 Replies)
Discussion started by: big123456
4 Replies
4. UNIX for Dummies Questions & Answers
I have two host ( hostA and hostB ) , now hostA can use " rsh -l userB hostB " to rsh to hostB without input the password , it work fine, but if I modify it to " rsh -l userB hostB -n "ls" " , it will pop the message "Permission denied." , could suggest what is wrong ? thx (1 Reply)
Discussion started by: ust
1 Replies
5. UNIX for Dummies Questions & Answers
hi friends,
i've access to three machines mc1,mc2,mc3,on which i can log in as root.
and in order to run a simple command on a remote machine(say remote) on which i cant log in,i use a command as;
# rsh remote ls
the above runs properly but if i do an ls on following it doesnt work
# rsh mc2... (1 Reply)
Discussion started by: mxms755
1 Replies
6. UNIX for Advanced & Expert Users
Hi All,
I want to execute a command from my Windows machine to Linux machine using RSH only
d:> rsh <Linux machine add> -l <user_name> pwd>dir
in linux machine users home directory in .rhosts file I entered the windows machine IP address and user name.
In linux etc/hosts.equiv file I... (1 Reply)
Discussion started by: sarwan
1 Replies
7. Solaris
Hello guys, I have a script in a Linux server, from where I go to 3 Sun servers and run process.
Now i have done an upgrade and increase 1 Sun server more, now i need to run the shell in the Linux Server (into the shell is rsh command), but when i try to do ir with the new Sun server, i hace the... (3 Replies)
Discussion started by: lestat_ecuador
3 Replies
8. AIX
How to configure rsh for different users in aix? (4 Replies)
Discussion started by: vjm
4 Replies
9. Solaris
How to enable rsh in solaris (7 Replies)
Discussion started by: durgaprasadr13
7 Replies
10. Red Hat
Hi,
I issue :
rsh ****.16.0.151 -l root ls -l /tmp
and I receive :
connect to address ***.16.0.151: Connection refused
Trying krb4 rsh...
In hosts file of remote (***.16.0.151) I have :
***.16.0.202 root
Can you help me ?
Thank you. (0 Replies)
Discussion started by: big123456
0 Replies
LEARN ABOUT MINIX
ifconfig
IFCONFIG(8) System Manager's Manual IFCONFIG(8)
NAME
ifconfig - configure a TCP/IP device
SYNOPSIS
ifconfig [-I ip-device] [-h ipaddr] [-n netmask] [-iv]
DESCRIPTION
Ifconfig initializes a TCP/IP device setting the IP address and/or netmask. It will report the address and netmask set. This command may
be used if the system has not been configured properly yet. It is only used at boot time to set a fixed address for a system without a
physical ethernet. Normally the inet task will find it out by itself from the RARP server.
OPTIONS
-h The decimal TCP/IP address to set.
-n The netmask to set.
-i Don't set the IP address or netmask if already set. This way ifconfig cannot interfere if the numbers have been found out by RARP.
-v Report IP address and netmask. This is the default action if there are no other options.
SEE ALSO
hostaddr(1), rarpd(8), set_net_default(8), boot(8).
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
IFCONFIG(8)