03-03-2008
Quote:
Originally Posted by
pupp
see if you can get a list of attached devices under prtconf or /etc/path_to_inst. off the top of my head i don't exactly remember which will give you better output. but you'll probably see bge0, ce0 and so on. try and plumb the device if you can find it.
its a vmware machine! so it should be vmnet0 or something like thet. but i don't know if solaris 9 runs in a vmware environment!
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Solaris
Hi all,
I just install solaris10 at home to learn b4 taking the sun courses. Can't get the internet on my IntelPC. I'm using cable thru SMC ezcard 10/100. I ran ifconfig -a and it only shows lo0. No hme0.
Pls help. (9 Replies)
Discussion started by: maag
9 Replies
3. Solaris
Hi Gurus
Im a fresher and im working.I installed solaris 10 on my windows PC(dual boot) but im not able plumb my interface..everytime i use ifconfig command and tried different interfaces like eri0,ce0 etc but its displaying that interface not found.I know that there is some problem with... (15 Replies)
Discussion started by: madanmeer
15 Replies
4. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT X11R4
ip-token
IP-TOKEN(8) Linux IP-TOKEN(8)
NAME
ip-token - tokenized interface identifier support
SYNOPSIS
ip token { COMMAND | help }
ip token set TOKEN dev DEV
ip token del dev DEV
ip token get [ dev DEV ]
ip token [ list ]
DESCRIPTION
IPv6 tokenized interface identifier support is used for assigning well-known host-part addresses to nodes whilst still obtaining a global
network prefix from Router advertisements. The primary target for tokenized identifiers are server platforms where addresses are usually
manually configured, rather than using DHCPv6 or SLAAC. By using tokenized identifiers, hosts can still determine their network prefix by
use of SLAAC, but more readily be automatically renumbered should their network prefix change [1]. Tokenized IPv6 Identifiers are described
in the draft [1]: <draft-chown-6man-tokenised-ipv6-identifiers-02>.
ip token set - set an interface token
set the interface token to the kernel.
TOKEN the interface identifier token address.
dev DEV
the networking interface.
ip token del - delete an interface token
delete the interface token from the kernel.
dev DEV
the networking interface.
ip token get - get the interface token from the kernel
show a tokenized interface identifier of a particular networking device. Arguments: coincide with the arguments of ip token set but the
TOKEN must be left out.
ip token list - list all interface tokens
list all tokenized interface identifiers for the networking interfaces from the kernel.
SEE ALSO
ip(8)
AUTHOR
Manpage by Daniel Borkmann
iproute2 28 Mar 2013 IP-TOKEN(8)