Network Interface Issue Post: 302170644

Sponsored Content

Operating Systems Solaris Network Interface Issue Post 302170644 by baraghun on Tuesday 26th of February 2008 08:15:56 AM

02-26-2008

Registered User

Network Interface Issue

Hi all,

Here im facing problem with NIC Interface with my X86 Version of Solaris Express, even after loading module for that Interface. So please check this below mentioned log for your use and get back to me ASAP.
- - - -- -- ------------------------------------------------------------------------------- -----
bash-3.00# more /etc/svc/volatile/network-physical:default.log

[ start + 1.22s Enabled. ]

[ start + 3.21s Executing start method ("/lib/svc/method/net-physical") ]

[ start + 3.37s Timeout override by svc.startd. Using infinite timeout ]

ifconfig: cannot open link "vfe0": DLPI link does not exist moving addresses from failed IPv4 interfaces:

vfe0 (couldn't move, no alternative interface).

[ Feb 26 12:09:26 Method "start" exited with status 96 ]
-------------------------------------------------------------------------- ---------------------

Waiting for earliest feedback.

Thank you

baraghun

View Public Profile for baraghun

Find all posts by baraghun

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

2. Solaris

Network interface issue

Hi All, I want to configure network into my system. i tried following in to configure the interface to find the name of interface #prtdiag |grep net i got following 0 PCI-1 33 1 network-SUNW, hme then i tried following #prtconf -v |grep net network, instance #0

3. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

4. Solaris

Network interface not recoginized

Hello, I have Windows and Solaris 10 installed on HP Pavalion. Both of the operating system are installed on separate drives. Network card is recognized on Windows but Solaris doesn't seem to recognize it for some reason. So far I have tried sys-unconfig but it didn't really help. Please...

5. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

6. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

7. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

8. Red Hat

Redhat disabling network interface - IRQ issue

Hi. I'm having problems on multiple Red Hat VM's (on esxi) whereby the network interface IRQ is disabled by the OS. This is the error from dmesg: command: Write(10): 2a 00 03 42 3f e0 00 00 08 00 mptscsih: ioc0: task abort: SUCCESS (sc=ffff81018b45c680) irq 67: nobody cared (try...

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT LINUX

svc.configd

svc.configd(1M)                                                                                                                    svc.configd(1M)

NAME

       svc.configd - Service Management Facility repository daemon

SYNOPSIS

       /lib/svc/bin/svc.configd

       svc.configd  is  the repository daemon for the Service Management Facility. svc.configd is invoked automatically during system startup, and
       restarted if any failures occur. svc.configd should never be invoked directly.

       Interaction with svc.configd is by way of libscf(3LIB) and the command line tools:svcs(1), svcprop(1), svcadm(1M), and svccfg(1M).

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE         |      ATTRIBUTE VALUE        |
       +-----------------------------+-----------------------------+
       |Availability                 |SUNWcsr                      |
       +-----------------------------+-----------------------------+

       svcs(1), svcprop(1), svcadm(1M), svccfg(1M), libscf(3LIB), attributes(5)

                                                                    27 Oct 2004                                                    svc.configd(1M)