Sponsored Content
Operating Systems Solaris Netra 240 Hard disk are not detected Post 302167052 by DukeNuke2 on Wednesday 13th of February 2008 10:47:10 AM
Old 02-13-2008
what have you done allready?
do you see the disk with "probe scsi-all" at obp level? or with "showdisks" at obp?
is the alias correct? check "devalias" and "printenv".
 

10 More Discussions You Might Find Interesting

1. Solaris

netra 240 difference

Hi, sunfire v240 and netra 240 are looks similar. system board, memory and processors are similar, then why netra 240 called as telco server? can anyone tell the difference. RJS (1 Reply)
Discussion started by: rajasekg
1 Replies

2. UNIX for Dummies Questions & Answers

Refurbished Netra 240 servers hangs after POST test

Hello everyone, I'm extremely new when it comes to SUN servers so bear with me and hopefully I can describe the issue I have accurately. At work we just received a refurbished SUN Netra 240 server. I was told to change some of the EEprom settings, and to do that I was to use a... (0 Replies)
Discussion started by: afferbwt
0 Replies

3. Solaris

SUN Netra 240 Boot error

Hi, When I am trying to boot my SUN Netra 240 Machine its giving some boot error. > {1} ok boot -i > Boot device: /pci@1c,600000/scsi@2/disk@0,0:a File and args: -i > Boot load failed. > The file just loaded does not appear to be executable. > {1} ok I tried to boot it from cdrom... (9 Replies)
Discussion started by: ppandey21
9 Replies

4. Solaris

Unable to access serial port from non-global solaris zone on netra 240

I am trying to use a serial communications device that is connected to /dev/ttyb on a netra 240 server. This is a solaris zone configuration using solaris 10 0910. I am able to access /dev/ttyb from the global zone but not throught he non-global zone. I have enabled all of the tty devices in my... (0 Replies)
Discussion started by: disagreeable
0 Replies

5. Linux

C++ Code to Access Linux Hard Disk Sectors (with a LoopBack Virtual Hard Disk)

Hi all, I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies

6. Solaris

solaris hard disk not detected

Dear all, I have a Sol 10 server. When I put df -h , it is showing the mount points of all file systems, but when I format the server it is showing the below output bash-3.00# format Searching for disks...done No disks found! Pl let me know what is the problem for this. ... (5 Replies)
Discussion started by: jegaraman
5 Replies

7. Hardware

[solved] Sun Netra X1 - Adding a Second Hard Drive

As the title suggests, I'm trying to install a second drive (really want an OS mirror) on a Sun Netra X1. I've taken the spacer out, and had a go at with the drill-press so now I have a nice HDD tray. Have installed an IDE drive in the tray, plugged in the power and data cables that were... (0 Replies)
Discussion started by: Smiling Dragon
0 Replies

8. Hardware

POST displays error sparc netra 240

Hi guys, when I power on my sun netra 240 server, it displays these error messages: 1. Notice: cpu 0 has 2048/2048 MB of memory disabled. 2. Error : The following devices are disabled dimm1. Please can anyone be kind enough to explain this for me? Thanks (2 Replies)
Discussion started by: cjashu
2 Replies

9. Red Hat

Unsupported hardware detected error for SSD hard drive

Hi, I am trying to install Oracle Linux 6.5 on vmware workstation 9, but during the installation i am getting popup box with below message. unsupported hardware detected The hardware ( or a combination thereof) is not supported by Oracle Linux) ....... My laptop is having SSD SM871... (1 Reply)
Discussion started by: suren424
1 Replies

10. Solaris

Fibre Channel link not ready on Netra 240

Hi, One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too. There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Discussion started by: solaris_1977
5 Replies
SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)			 systemd-machine-id-commit.service		      SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)

NAME
systemd-machine-id-commit.service - Commit a transient machine ID to disk SYNOPSIS
systemd-machine-id-commit.service DESCRIPTION
systemd-machine-id-commit.service is an early boot service responsible for committing transient /etc/machine-id files to a writable disk file system. See machine-id(5) for more information about machine IDs. This service is started after local-fs.target in case /etc/machine-id is a mount point of its own (usually from a memory file system such as "tmpfs") and /etc is writable. The service will invoke systemd-machine-id-setup --commit, which writes the current transient machine ID to disk and unmount the /etc/machine-id file in a race-free manner to ensure that file is always valid and accessible for other processes. See systemd-machine-id-setup(1) for details. The main use case of this service are systems where /etc/machine-id is read-only and initially not initialized. In this case, the system manager will generate a transient machine ID file on a memory file system, and mount it over /etc/machine-id, during the early boot phase. This service is then invoked in a later boot phase, as soon as /etc has been remounted writable and the ID may thus be committed to disk to make it permanent. SEE ALSO
systemd(1), systemd-machine-id-setup(1), machine-id(5), systemd-firstboot(1) systemd 237 SYSTEMD-MACHINE-ID-COMMIT.SERVICE(8)
All times are GMT -4. The time now is 12:46 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy