assigning ip to second interface Post: 302163399

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

assigning variables

Before I even attempt this, is it possible to grep for a pattern, maybe a partial sentence like "go to page 3", assign that to a variable and then use awk or something to pull out the 3 and assign it to a variable? So first I would have Gotopg = "go to page 3" then page = 3

2. HP-UX

Assigning IP's

hi all, i want to know where i can add and IP address so when i do a "w", i can see what IP is assigned to which tty? i know in tru64 you just added an entry to /etc/hosts. this does not seem to be the case with hpux. thanks

3. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI...

4. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you

5. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

6. Shell Programming and Scripting

Assigning variables

i have variables RECIPIENTS_DEVL,RECIPIENTS_UACC,RECIPIENTS_PROD i have a case statement to get the phase variable: case ${WMD_UPHASE1} in u) WMD_UPHASE4=UACC;; i) WMD_UPHASE4=DEVL;; p) WMD_UPHASE4=PROD;; d) WMD_UPHASE4=DEVL;; *) WMD_UPHASE4=DEVL;; esac I am unable to...

7. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

8. UNIX for Advanced & Expert Users

C program to detect duplicate ip address if any after assigning ip address to ethernet interface

Hi , Could someone let me know how to detect duplicate ip address after assigning ip address to ethernet interface using c program

9. UNIX for Dummies Questions & Answers

Assigning ipv6 to bonding interface - getting old as well as changed ipv6 in ifconfig output

Hi, I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your...

LEARN ABOUT DEBIAN

setether

SETETHER(8)						      System Manager's Manual						       SETETHER(8)

NAME

       setether - Set the ethernet address for use with DECnet

SYNOPSIS

       setether <if> [<if>...]|all [options]

DESCRIPTION

       Set ethernet MAC address on ethernet adaptors

       This  script should be run at system startup. It will change the ethernet hardware (MAC) address of any or all ethernet interfaces to match
       the DECnet node address. DECnet requires that the MAC address of all ethernet adaptors running the protocol be set approriately.  If you do
       not run setether then you must change the ethernet address in some other way for DECnet to work.
       By  default no ethernet interfaces will have their MAC addresses changed by setether, if you specify all then all interfaces name eth* will
       be changed, otherwise a list of interface names can be specified.  setether will enable (UP) all interfaces it changes  the  MAC  addresses
       of.
       (2.4  only) The first interface specified on the command-line will also be made the default interface for DECnet operations (ie attempts to
       contact nodes not in the neighbour table will be done over this interface).
       This script must be run with the interface inactive, it is normally run from /etc/init.d/decnet before TCP/IP starts up.

EXAMPLES

       set the MAC address of eth0.

	   # /sbin/setether eth0

       set the MAC address of all ethernet interfaces

	   # /sbin/setether all

HELPFUL HINTS

       If you have multiple ethernet cards on your system and they are connected to the the same network you should specify which one you want	to
       use  for DECnet communication on the setether command line, otherwise they will both be given the same MAC address and this is probably not
       what you want.
       Running DECnet on multiple ethernet interfaces only works under Linux 2.4. If you are running Linux 2.2 then  the  interface  name  on  the
       setether command line must match the one in /etc/decnet.conf(5).

SEE ALSO

       decnet.conf(5), dntype(1), dndir(1), dndel(1), dnetd(8), dnping(1)

DECnet utilities						   March 01 2001						       SETETHER(8)