01-31-2008
5.0.7 does not automatically detect new hardware.
Run 'mkdev tape'
and select the correct host adapter and input the scsi id, and lun information.
This procedure will rebuild the kernel, and after a re-boot you should see the tape drive in the hardware list at boot. (or check /usr/adm/messages for the same information if you miss seeing it during the boot.)
10 More Discussions You Might Find Interesting
1. Linux
Hi,
I want to install LINUX on my laptop. I have a 2GHZ,1GB RAM and HDD is not partitioned. I donot want to touch this HDD and I have external HDD of 200GB. Can I install LINUX on this external HDD?. I would like system to detect linux only when I connect my external hard drive. else system should... (5 Replies)
Discussion started by: sureshht
5 Replies
2. SCO
I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies
3. SCO
Hi there
We are trying to install SCO OpenServer v5.07 on an HP ML350 G5 server.
I have downloaded the drivers from HP's website, but are getting nowhere. (I feel that I am going round in circles - every time I google for the drivers, I end up here.) :(
What happens is we create the driver... (12 Replies)
Discussion started by: The_Librarian
12 Replies
4. Solaris
I am looking for this document UNIX Configuration Guide on the HP StorageWorks Tape.
I need a procedure to install StorageWorks DAT 40 internal tape drive C5668A. (10 Replies)
Discussion started by: real-chess
10 Replies
5. Solaris
I need to install a raid HBA internal card on a T5240. The reason is I have
more drives and the current mother board controller does not support more
than 4 drives.
My question is I have raidctl set up on current drives. If I install new HBA
card do I have to delete current raidctl and... (3 Replies)
Discussion started by: photon
3 Replies
6. Solaris
Hi all
i would like to ask some suggests about my next job!
I have to install a new Sun Netra T5220, with an additional internal StorageTek SAS HBA Raid.
The problem come in if every disk is now controlled by the HBA, how can I install the OS?
No disk is being detected by the OS.
SAS card... (2 Replies)
Discussion started by: kakabobo
2 Replies
7. Solaris
i was given a task which needs to perform a raid 1 on the boot disk, and 4 other disks on raid 10.
Is there any other alternative in installing solaris 10 other than through network installation?will be using solaris update 6.
while reading through the user guide i got pretty confuse.
... (1 Reply)
Discussion started by: monstar1407
1 Replies
8. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
9. OS X (Apple)
Hi,
As I did not find any specific group for this question, i am putting it here.
Can I install Mac OS on an external hard disk?
Is this possible or not? I know it is very hard to install mac os on non-mac hardwares. I have a dell inspiron laptop and i want to use mac from external hdd.
... (1 Reply)
Discussion started by: sanzee
1 Replies
10. Solaris
Dear All,
I have been trying to move my existing Solaris Installation (x86, 10/08) to a bigger HDD.
So I created a 22 cylinder boot partition and used the rest of the space for a Solaris2 partition. Then I created slices same size like on my current disk.
I copied all files with cpio and... (3 Replies)
Discussion started by: BigT79
3 Replies
LEARN ABOUT REDHAT
amtape
AMTAPE(8) System Manager's Manual AMTAPE(8)
NAME
amtape - user interface to Amanda tape changer controls
SYNOPSIS
amtape config command [ command options ]
DESCRIPTION
Amtape performs tape changer control operations. It uses the underlying tape changer script defined by the tpchanger option for a particu-
lar Amanda configuration as specified by the config argument.
Tape changers maintain a notion of the current and next slot for each configuration. These may or may not correspond to an actual physical
state of the device, but do tend to minimize searching through the tape storage slots. If the desired tape is in the current slot, it is
likely the next tape needed is in the next slot rather than at some random position in the storage slots.
See the amanda(8) man page for more details about Amanda.
COMMANDS
reset Reset the tape changer to a known state. The current slot is set to the first slot. Other device-specific side effects may occur.
Some gravity stackers need to be reset to the top position by hand. This command notifies Amanda the stacker is back in that posi-
tion.
eject If a tape is loaded in the drive, it is ejected and returned to the slot from which it was loaded.
clean If a cleaning tape is defined for the changer, it is used to clean the drive.
show Show the contents of all slots. This can be slow.
label label
Search for and load the Amanda tape with label label.
taper Perform the taper scan algorithm. Load the next tape in the configuration's tape sequence, or a fresh tape with a suitable label.
device Display the name of the current tape device on stdout.
current
Display the current slot.
update Update the changer label database, if it has one, to match the tapes now available.
slot slot
Eject any tape in the drive and put it away, then load the tape from slot slot and reset current.
slot current
Eject any tape in the drive and put it away, then load the tape from the current slot.
slot prev
Eject any tape in the drive and put it away, then load the tape from the previous slot and reset current.
slot next
Eject any tape in the drive and put it away, then load the tape from the next slot and reset current.
slot first
Eject any tape in the drive and put it away, then load the tape from the first slot and reset current.
slot last
Eject any tape in the drive and put it away, then load the tape from the last slot and reset current.
slot advance
Eject any tape in the drive and put it away. Advance current to the next tape, but do not load it.
This is useful with non-gravity stackers to unload the last tape used and set up Amanda for the next run. If you just use eject,
the current tape will be mounted again in the next run, where it will be rejected as being still in use, ejected and the next tape
requested. Using slot next followed by eject does an unnecessary mount.
Note: most changers optimize the slot commands to not eject the loaded tape if it is the one being requested.
AUTHOR
James da Silva <jds@cs.umd.edu>
University of Maryland, College Park
SEE ALSO
amanda(8)
AMTAPE(8)