01-26-2008
i connect through ethernet
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI..
i was wondering if someone out there can help me setup my internet connection.... i have no clue how to set it up.. could you please tell me step by step how to set it up.. i have a static ip, im using a cable modem to connect. my os is solaris 8. Please email me at lil_souldier@hotmail.com... (2 Replies)
Discussion started by: souldier
2 Replies
2. UNIX for Dummies Questions & Answers
I am using solaris 10 with pentium 3. I have two network cards but none of them come up when i run <ifconfig -a> in command line. The two cards I have are : Linksys LNE 100TX and Netgear FA311. Does solaris 10 support these NICs or do I have to dowload the drivers for them.
If so, can anyone... (1 Reply)
Discussion started by: fidjouss
1 Replies
3. UNIX for Dummies Questions & Answers
Hello,
Which services and daemons are used in Solaris in order to connect to Solaris10 from windows-Reflection ?
Please just give me a brief information, I can read details from other resources.
Thanks (0 Replies)
Discussion started by: XNOR
0 Replies
4. IP Networking
Hi,
I am using VMWARE and when I have the network connection set to NAT and the VM set to DHCP I get internet connection. But when I set the connection to BRIDGED and assign a static IP address I loose internet connection. I have used netconfig to manually assign the IP Address, GATEWAY, and... (5 Replies)
Discussion started by: mojoman
5 Replies
5. Solaris
Installed Sun Solaris 10 (5/09) on vmware 6.0 but system is not connecting to internet.
when I check "ipconfig /all" I do not get any DNS Suffix name -- neither for vmnet1 and vmnet8 nor for local ethernet IP. Default gateways are 192.168.1.1 and 192.168.1.2
1. Created /etc/resolv.conf
domain... (1 Reply)
Discussion started by: johnjerry
1 Replies
6. Solaris
HI Admins,
I am trying to run internet on solaris 10 on vmware workstation 6.5..
I have vista on my laptop.
I tried following:
1. enabling DHCP and NAT on virtual network editor...for NAT I tried
vmnet host:vmnet0 start/stop.
2. ifconfig -a showing pcn0 running for both ipv4 and ipv6....... (1 Reply)
Discussion started by: snchaudhari2
1 Replies
7. Solaris
Hi Experts,
In our env, we have around 100 more solaris 8,9,10 servers,
we quaterly apply patches & emergency fixes, for this we take prior OS Ufsdump bkp,
In order to reduce the efforts to go DC & load each time the tapes on all servers & take the ufsdump backup, we planned to set up a... (2 Replies)
Discussion started by: fizan
2 Replies
8. Solaris
I have a solaris 10 on my laptop. I want to let my internet work.
Command: ifconfig -a
Return:
lo: ...
e1000g0: ...
I dont know what else to setup so when I open firefox, I have access to internet. Can anyone show me how to do the setting? Thanks a lot. (1 Reply)
Discussion started by: dbahaha
1 Replies
9. Solaris
Hi all, I have setup Solaris 10 OS on my home Sparc (Blade 1500) box. I also setup CDE (Common Desktop Environment).
The box has Network card with 6 connections available for Internet, So I hooked up a hard-wired link from my router to the first slot. The light is green on both ends.
Now, how... (2 Replies)
Discussion started by: steve701
2 Replies
10. Red Hat
Hi all, I setup redhat in VMware and I connected to internet, so I want setup sofware for redhat over internet what is command I used ? Are you understand my question, my ability of english is not good, such as I want setup dhcp packet I must used a command ? (yum... or...apt-get...or rpm... ?... (4 Replies)
Discussion started by: ilinux9
4 Replies
LEARN ABOUT DEBIAN
setether
SETETHER(8) System Manager's Manual SETETHER(8)
NAME
setether - Set the ethernet address for use with DECnet
SYNOPSIS
setether <if> [<if>...]|all [options]
DESCRIPTION
Set ethernet MAC address on ethernet adaptors
This script should be run at system startup. It will change the ethernet hardware (MAC) address of any or all ethernet interfaces to match
the DECnet node address. DECnet requires that the MAC address of all ethernet adaptors running the protocol be set approriately. If you do
not run setether then you must change the ethernet address in some other way for DECnet to work.
By default no ethernet interfaces will have their MAC addresses changed by setether, if you specify all then all interfaces name eth* will
be changed, otherwise a list of interface names can be specified. setether will enable (UP) all interfaces it changes the MAC addresses
of.
(2.4 only) The first interface specified on the command-line will also be made the default interface for DECnet operations (ie attempts to
contact nodes not in the neighbour table will be done over this interface).
This script must be run with the interface inactive, it is normally run from /etc/init.d/decnet before TCP/IP starts up.
EXAMPLES
set the MAC address of eth0.
# /sbin/setether eth0
set the MAC address of all ethernet interfaces
# /sbin/setether all
HELPFUL HINTS
If you have multiple ethernet cards on your system and they are connected to the the same network you should specify which one you want to
use for DECnet communication on the setether command line, otherwise they will both be given the same MAC address and this is probably not
what you want.
Running DECnet on multiple ethernet interfaces only works under Linux 2.4. If you are running Linux 2.2 then the interface name on the
setether command line must match the one in /etc/decnet.conf(5).
SEE ALSO
decnet.conf(5), dntype(1), dndir(1), dndel(1), dnetd(8), dnping(1)
DECnet utilities March 01 2001 SETETHER(8)