Sponsored Content
Operating Systems Solaris How to force the LAN interface running on 10M Post 302160867 by DukeNuke2 on Wednesday 23rd of January 2008 01:53:29 AM
Old 01-23-2008
use this script:
http://docs.cirkva.net/Sun/Solaris/Eis/S68net-tune
read the first few lines on how to use it!
 

9 More Discussions You Might Find Interesting

1. Solaris

How to configure private LAN and coporate LAN on the same machine-Solaris10

Hi , I am trying to configure a private LAN and corporate LAN on the same machien on Solaris 10. How can I achieve this? Thanks (1 Reply)
Discussion started by: deedee
1 Replies

2. UNIX for Advanced & Expert Users

Double question: Apache mod_proxy and force connection over specific interface

Double question here ... Running on Debian Etch and Apache 2.0 1) Using mod_proxy and/or mod_proxy_http in apache 2.0. The basics of using mod_proxy are pretty simple so long as you're using a static config. I'm trying to figure out how to do it dynamically - that is, allow the entry of a... (4 Replies)
Discussion started by: Halfwalker
4 Replies

3. IP Networking

Solaris 9 new pumbed interface will not enter a RUNNING state

I'm trying to plumb a new interface bge1 on my machine: root@obms2-com-indianapolis-in:/root# ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet... (3 Replies)
Discussion started by: R37ribution
3 Replies

4. Solaris

how to force e1000g0 interface in solaris 10

Hi all, I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot. But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands. ... (1 Reply)
Discussion started by: mailbox80
1 Replies

5. IP Networking

Local Lan, no-ip directed DNS forward, surf within lan

Hi, We have a website running on a local centos 5.4 surfer, static IP. The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server. My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine. However, we cannot see... (3 Replies)
Discussion started by: lawstudent
3 Replies

6. Red Hat

blue screen to config lan interface

I use red hat linx ES 4 ,5 , how can I start up attached screen to config the lan interface in command mode ??? Please advice in detailed ?? (1 Reply)
Discussion started by: chuikingman
1 Replies

7. Red Hat

iptable port forwarding between two lan interface

Hi, How can I config iptables to allow port forwarding from one WAN interface to second lan interface . In my system I have one wan interface 61.93.204.56 (eth0),and lan interface 10.2.1.52(eth1) I want to make port forward port no 22 from 61.93.204.56 to port 22 , 10.2.1.52 , tcp and udp... (1 Reply)
Discussion started by: chuikingman
1 Replies

8. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

9. Solaris

Interface e1000g0 not showing in running state

Hello all, I have a sun server SunOS PNR1RAD01 5.10 Generic_144488-09 sun4v sparc SUNW,Netra-T5220 where i have an interface e100g0. This was earlier in running state but now this doesnt show running state. I tried to reset the interface, checked the cable but it did not help. Can nyone pls... (10 Replies)
Discussion started by: rajjat2
10 Replies
uri_urn(3tcl)					    Tcl Uniform Resource Identifier Management					     uri_urn(3tcl)

__________________________________________________________________________________________________________________________________________________

NAME
uri_urn - URI utilities, URN scheme SYNOPSIS
package require Tcl 8.2 package require uri::urn ?1.1.2? uri::urn::quote url uri::urn::unquote url _________________________________________________________________ DESCRIPTION
This package provides two commands to quote and unquote the disallowed characters for url using the urn scheme, registers the scheme with the package uri, and provides internal helpers which will be automatically used by the commands uri::split and uri::join of package uri to handle urls using the urn scheme. COMMANDS
uri::urn::quote url This command quotes the characters disallowed by the urn scheme (per RFC 2141 sec2.2) in the url and returns the modified url as its result. uri::urn::unquote url This commands performs the reverse of ::uri::urn::quote. It takes an urn url, removes the quoting from all disallowed characters, and returns the modified urls as its result. BUGS, IDEAS, FEEDBACK This document, and the package it describes, will undoubtedly contain bugs and other problems. Please report such in the category uri of the Tcllib SF Trackers [http://sourceforge.net/tracker/?group_id=12883]. Please also report any ideas for enhancements you may have for either package and/or documentation. KEYWORDS
rfc 2141, uri, url, urn CATEGORY
Networking uri 1.1.2 uri_urn(3tcl)
All times are GMT -4. The time now is 08:23 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy