Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: /etc/rc.d/netif wont add default gateway
Top Forums UNIX for Dummies Questions & Answers /etc/rc.d/netif wont add default gateway Post 302148996 by rdns on Tuesday 4th of December 2007 02:22:39 PM
Old 12-04-2007
sadly no answer to this
i am asking because i have told as for my /etc/rc.conf changes to take effects, i must use /etc/rc.d/netif to restart the services
but i found it later that i will be disconnected from my remote terminal just because /etc/rc.d/netif wont care about routing
it's a pain to get connected back to the remote terminal

i've found out later that i must use /etc/rc.d/routing together with netif
for e.g:
Code:
/etc/rc.d/netif restart; /etc/rc.d/routing restart

/etc/rc.d/routing will re add back the routing tables after it has been flushed by /etc/rc.d/netif

thanks
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Add route gateway -> Restart !! Lose it

:confused: Hi: I donīt know how to add route gateway and when restart the machine lose this route and put other. In SCO ver 5.6 Enterprise write: etc\route delete gateway route add gateway 199.199.1.1. so , netstat -rn to see if has change -> all ok Restart -> !!!... (2 Replies)
Discussion started by: AlvaroD
2 Replies

2. UNIX for Dummies Questions & Answers

Aix Add Gateway

I have a AIX lates OS. I;m trying to setup a remote office using a telnet section and for some reazon it wont let me login in to the server. I've done this type of configuration on a SCO 5.0.6 . In SCO there is a file call S99route and that is where you put the gateway and it works just... (3 Replies)
Discussion started by: josramon
3 Replies

3. UNIX for Dummies Questions & Answers

How to add 2 gateway routes?

I need some help adding routes in sco. I am using SCO Openserver 5.0.4. Basically I have 2 gateways here. The first is 10.15.1.1 and allows me access to the rest of the computers in the office and in other offices. The other gateway is 10.15.10.2 and is the sonicwall that will allow access... (3 Replies)
Discussion started by: cstovall
3 Replies

4. HP-UX

How to add another default gateway

I am using HP-UX 11i and I need to add another default gateway. how can I do that ? (3 Replies)
Discussion started by: salhoub
3 Replies

5. Solaris

Add gateway

Hi Community, I've a question about network adaptors. I've installed Solaris 10 configuring the ce0 port with an IP(10.23.8.15) , an interface_name (first) and a gateway(10.23.8.1) . I need to change the name of the interface ce0 and to configure another interface (ce1) with another... (1 Reply)
Discussion started by: Sunb3
1 Replies

6. Linux

GNUGK-How to setup static gateway to gateway routing

Dear Sir I am a newbie in the world of IP telephony. I have been working with Asterisk PBX (SIP) and Cisco Call Manager (MGCP) but now I am learning on how to work GNUGK for H.323 Gatekeeper. I am having a problem, configuring static call routing on GNUGK in the section ... (0 Replies)
Discussion started by: mfondoum
0 Replies

7. Solaris

how to add a default gateway in a zone of different VLAN of global zone

Hi Greetings... I have an issue in connecting the zone from outside the network and it is because of default gateway. I can ping default gateway from inside the zone and not able to ping from global zone due to different VLAN issue. If i add two different gateways and restart network services,... (2 Replies)
Discussion started by: vvpotugunta
2 Replies

8. Solaris

Cannot add gateway

Hi, OS: Solaris 11.2 64bit IP address: 172.16.10.10 Netmask: 255.255.254.0 Gateway: 172.16.2.254 From windows box, i can set and ping gateway. IP address is same segment with windows box. But on solaris i cannot set gateway. route add default 172.16.2.254 add net default: gateway... (6 Replies)
Discussion started by: mzainal
6 Replies

9. Linux

Unable to add route with a specific gateway IP

Hi, This is the routing table on a RHEL 7 server : # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.132.81.145 0.0.0.0 UG 100 0 0 eno49 10.132.81.144 0.0.0.0 255.255.255.240 U 100 0 0 eno49... (4 Replies)
Discussion started by: anaigini45
4 Replies

10. UNIX for Beginners Questions & Answers

Inconsistency between RedHat 6.5 global gateway and single gateway leads to loss of default gateway

Dear friends I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies

LEARN ABOUT MOJAVE

nodesave

NODESAVE(8)						   Linux System Managers Manual 					       NODESAVE(8)

NAME

       nodesave - Saves NET/ROM routing information

SYNOPSIS

       nodesave [-p path] [-v] [filename]

DESCRIPTION

       Nodesave  saves	the contents of the /proc filesystem entries for the NET/ROM routing tables. The output of the program is in the form of a
       Bourne shell script that calls nrparms(8) to recreate the NET/ROM routing information. If no filename is given on  the  command	line,  the
       program writes the script to stdout.

       Typically  nodesave  would  be  used  when  taking  a system off-air so that the NET/ROM routing may be quickly restored when the system is
       brought back on-line.

OPTIONS

       -p path	 Set the path to the nrparms binary. This only affects the output of the program. Default is /usr/sbin.

       -v	 Display the version.

FILES

       /proc/net/nr_neigh
       /proc/net/nr_nodes

SEE ALSO

       netrom(4), netromd(8), nrparms(8).

AUTHOR

       Tomi Manninen OH2BNS <oh2bns@sral.fi>

Linux								    4 July 1999 						       NODESAVE(8)
All times are GMT -4. The time now is 06:56 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy