Sponsored Content
Full Discussion: NIC question!
Special Forums IP Networking NIC question! Post 302147502 by sysgate on Tuesday 27th of November 2007 08:37:45 AM
Old 11-27-2007
I guess it is Smilie can you please post the output of "/sbin/ifconfig" and shed some light on "internet sharing". Usually eth0 is the first NIC you have, and eth1 is the second one, but it could be virtual interface as well. Do you have these two NICs physically installed on your box ?
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

NIC driver building question

I'm way confused. I loaded RH 7.1 on an old P-75 Compaq. IT has an EtherExpress pro/100 card in it and I have that attached to the optional port on our firewall with a crossover....I can't seem to get the card to negotiate with the firewall...it's currently 100Meg at Half duplex. I'm at a loss... (3 Replies)
Discussion started by: kwalter
3 Replies

2. UNIX for Dummies Questions & Answers

nic question...

Hi everybody, I want to know if there is a command for solaris or linux to have nic answers, like: register entity technical contact an so on, for a domain. I know I can do that fron the nic's site, but some guy told me there is a command to do that, but I forget it. I try dig, host,... (2 Replies)
Discussion started by: piltrafa
2 Replies

3. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks (2 Replies)
Discussion started by: alert0919
2 Replies

4. UNIX for Advanced & Expert Users

Question on NIC and ndd command

I have a T2000 server which has 4 e1000g NIC cards How do I configure each of it for 1Gbit full duplex and turnoff autonegotiation. Please assist Thanks (4 Replies)
Discussion started by: Tirmazi
4 Replies

5. UNIX for Dummies Questions & Answers

NIC card monitoring traffic question

Folks; I have 2 NIC cards on my SUSE Linux server. One of them was reporting receive errors for a while now it's OK, but i'd like to monitor it. Is there any command i can run to tell me the usage in the past or give me a history of traffic and the speed that going on this specific card? I... (1 Reply)
Discussion started by: Katkota
1 Replies

6. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

7. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies

8. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

9. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
Match-all classifier in tc(8)					       Linux					     Match-all classifier in tc(8)

NAME
matchall - traffic control filter that matches every packet SYNOPSIS
tc filter ... matchall [ skip_sw | skip_hw ] [ action ACTION_SPEC ] [ classid CLASSID ] DESCRIPTION
The matchall filter allows to classify every packet that flows on the port and run a action on it. OPTIONS
action ACTION_SPEC Apply an action from the generic actions framework on matching packets. classid CLASSID Push matching packets into the class identified by CLASSID. skip_sw Do not process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter- face, operation will fail. skip_hw Do not process filter by hardware. EXAMPLES
To create ingress mirroring from port eth1 to port eth2: tc qdisc add dev eth1 handle ffff: ingress tc filter add dev eth1 parent ffff: matchall skip_sw action mirred egress mirror dev eth2 The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it that mirrors the packets to device eth2. To create egress mirroring from port eth1 to port eth2: tc qdisc add dev eth1 handle 1: root prio tc filter add dev eth1 parent 1: matchall skip_sw action mirred egress mirror dev eth2 The first command creats an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a matchall filters on it that mirrors the packets to device eth2. To sample one of every 100 packets flowing into interface eth0 to psample group 12: tc qdisc add dev eth0 handle ffff: ingress tc filter add dev eth0 parent ffff: matchall action sample rate 100 group 12 SEE ALSO
tc(8), iproute2 21 Oct 2015 Match-all classifier in tc(8)
All times are GMT -4. The time now is 11:03 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy