11-26-2007
Restore from HP Tape Drive
Here is the scenario. We have an billing system that ran on SCO 5.0.6. The HP Netserver went dwon, along with SCSI disks. They are unretrievable. I installed an IDE HDD, and reinstalled SCO. I am not too familiar w/ SCO or UNIX, and need to know how to install Tape drive, and how to restore from tape drive. I have tried mkdev tape to install, but I am having some difficulties. I am assuming, once drive is installed and working, I will then run tar tvf /dev/rct0 | page to view contents of tape, then tar xvf /dev/rct0 to restore all data and overwrite current SCO installation. Please advise. Any help will be greatly appreciated. Thanks. - Jon
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi. I have been having problems with restoring from a tape backup. I use the following cpio command:
find / -print | cpio -ouvB > /dev/rStp0
After running this cpio command, the screen will display all files, but when I try to read or restore the tape I get the following error:
Tape input... (1 Reply)
Discussion started by: cstovall
1 Replies
2. Filesystems, Disks and Memory
I have been restoring from tape some old data. I have done quite a few tapes and have had no problems until now.
The command I am running is "dd if=/dev/rmt/1hbn bs=1024 | tar -pBxF - ".
This is the second tape have have come up with the error "Not enough space". This tape has a couple of... (1 Reply)
Discussion started by: mtoombs
1 Replies
3. HP-UX
I am trying to do a restore on a backup tape (DDS2) and am having a little trouble. For one, I dont know how the tape was made, whether is was tar, cpio, dump..etc. Anyone know how to restore a tape without knowing the format of the backup? (5 Replies)
Discussion started by: bake255
5 Replies
4. AIX
Hello everyone
I have a tape with some information that I got
to restore, the tape was made with the fbackup
command in a hp box.
My question is that I have to restore in a Ibm
box, how can I do this ?
Thanks in advance (1 Reply)
Discussion started by: lo-lp-kl
1 Replies
5. UNIX for Dummies Questions & Answers
Hi All,
I have an old Unix system used by a client as a backup server.I installed an Exabyte tape drive and on restarting the server and during POSTs, the system recognizes the tape drive with its scsi id. On running the command devstat -IAF, the system sees the tape drive quite well.
When... (1 Reply)
Discussion started by: ezleone
1 Replies
6. Solaris
I have a T2000 server that is JumpStarted with Solaris 10 from the JumpStart server. Host name and IP address is changed after that. Then we backup the server using FLAR to tape:
root.damas# date; flarcreate -c -t -n "Sol10_cairo_image" -a "engineering@starsolutions.com" -R / /dev/rmt/0n ;... (2 Replies)
Discussion started by: StarSol
2 Replies
7. Solaris
Hope someone can help me here...
I've got to restore an E450 with 300MHz cpus which was running Solaris 2.6 from tape. Regrettably the boot drive has failed.
I've access to the first release of Solaris 2.6 CD's and to a set of Solaris 9 CD's.
I remember that different E450 CPUs needed different... (1 Reply)
Discussion started by: pamplemousse
1 Replies
8. Emergency UNIX and Linux Support
Hi
I recently deleted my /etc but I had a backup on tape. I was able to boot the server with a cd-rom and mounted the /c1t0d0s0 which is where the root directory resides. However when I tried to restore the backup with tar xvf /dev/rmt/0n I wasn't successful even though I was able to use the tar... (2 Replies)
Discussion started by: rahmantanko
2 Replies
9. AIX
Hi,
I have taken a backup of a directory on my tape in using below command
cd /backup
find * -print|backup -ivf '/dev/rmt0' '-U' |tee -a /syslogs/backup.log and output appear in below format.
a 0 rman-before-08032014
a 58403323904... (2 Replies)
Discussion started by: m_raheelahmed
2 Replies
pxfw(8) pxfw 0.5 pxfw(8)
NAME
pxfw - Firmware flashing tool for Plextor CD/DVD devices
SYNOPSIS
pxfw -l
pxfw -d DEVICE [-if firmware.bin] [-u] [-f] [-v]
pxfw -d DEVICE [-e] [-r] [-t] [-v]
DESCRIPTION
pxfw is the linux firmware flasher for Plextor CD and DVD drives. Remove any disks before flashing.
FEATURES
You can flash the firmware of these drives:
Plextor Premium, Premium-2, PX-712, PX-716, PX-755 and PX-760.
DEVICE
can be an IDE, SCSI, SATA, USB or FireWire connected optical drive. Not all SATA controller support all Plextor features.
Linux:
/dev/hdX: IDE device
/dev/scdX: Linux 2.4: SATA, SCSI, USB device, or IDE device via ide-scsi emulation
/dev/srX: Linux 2.6: IDE device via new ATA layer, SCSI or USB device
OpenBSD/NetBSD:
/dev/rcdX
FreeBSD:
/dev/cd: SCSI device
/dev/acd: ATA device
MacOS X:
/dev/disk:
win32:
C:,D:,E:, ... X:,Y:,Z:
OPTIONS
-l scan busses for all available CD and DVD devices
-if select inputfile. Specify the firmware binary file, which should
be written to DEVICE.
-u proceed update. When the firmware checksum test has succeeded,
write firmware to DEVICE.
-f force flashing. Even if DEVICE is not recognized, or firmware.
checksum has failed, firmware writing will be forced.
Handle with care.
-e read EEPROM from DEVICE.
-r reboot the device.
-t test which opcodes are supported by the device.
-v debug.
EXAMPLES
pxfw -d /dev/hdc -if 755_1.07.bin -u
writes firmware file 755_1.07.bin into Master Drive on Secondary IDE-Port.
pxfw -d /dev/sr3 -e -oe file.foo
reades EEPROM from device /dev/sr3 and writes it to file.foo.
please report man page improvements to T.Maguin@web.de
Gennady ShultZ Kozlov 02 April, 2009 pxfw(8)