Hi,
I have a problem to use grep in my script .
If I want to grep the file for example : PTWO9089.txt
The code below works .
grep ^PONE
But, I dont know on how to grep the file like this 9066PTWO.txt
I'll try to use this code :
grep PTWO^ ,but it doesn't work.
For your info, the... (4 Replies)
Hello All. I have an output file which contains the phrase "Total DFT Energy =" and then a number. This occurs many times in the output file, and what I want is to pipe the numbers (which are all different) to a file so I can plot them. How do I grep "Total DFT Energy =" and then get the numbers... (3 Replies)
Hi,
Suppose,
DBconnection=jdbc: oracle:thin:@(DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=x.x.x.x)(PORT=YYYY))(LOAD_BALANCE=yes)(CONNECT_DATA=(SERVER=DEDICATED)(SERVICE_NAME=project_db1)))
This is a part of a file <filename> . I Need to get the value of SERVICE_NAME from this line…
The... (4 Replies)
hi all,
i need to combine these files into one csv file.
Bounce_Mail_Event_Daily_Report_01_Jul_2012.csv
Bounce_Mail_Event_Daily_Report_02_Jul_2012.csv
Bounce_Mail_Event_Daily_Report_03_Jul_2012.csv
Bounce_Mail_Event_Daily_Report_04_Jul_2012.csv... (10 Replies)
Hi,
I have 80 large files, from which I want to get a specific value to run a Bash script. Firstly, I want to get the part of a file which contains this:
Name =A
xxxxxx
yyyyyy
zzzzzz
aaaaaa
bbbbbb
Value = 57
This is necessary because in a file there are written more lines which... (6 Replies)
consider below file contents
cat myOutputFIle.txt
8 CCM-HQE-ResourceHealthCheck:
Resource List :
No RED/UNKNOWN resource Health entries found
----------------------------------------------------------
9 CCM-TraderLogin-Status:
Number of logins: 0... (4 Replies)
Hi,
I have a file with thousands of lines as below
INSERT INTO T_DIM_CLNT(CLNT_KY,CLNT_OBJ_ID,ISI_CLNT_ID,OPERN_ID,CLNT_NM,PRMRY_SIC_CD,PRMRY_SIC_DSC,RET_AGE_NBR,REC_CRT_TS,REC_DATA_EXTRC_TS,ETL_LOG_KY)
VALUES ( ?, ?, ?, ?, ?, ?, ?, ?, ?, ?, ?)... (5 Replies)
Hello,
I have a log file that has several sections "BEGIN JOB, End of job" like in the following example:
19/06/12 - 16:00:57 (27787398-449294): BEGIN JOB j1(27787398-449294) JOB1
19/06/12 - 16:00:57 (27787398-449294): DIGIT: 0
number of present logs : 1
19/06/12 - 16:00:57... (4 Replies)
Hi All,
We've a VDI infrastructure in AWS (AWS workspaces) and we're planning to automate the process of provisioning workspaces. Instead of going to GUI console, and launching workspaces by selecting individual users is little time consuming. Thus, I want to create them in bunches from AWS CLI... (6 Replies)
Discussion started by: arun_adm
6 Replies
LEARN ABOUT NETBSD
split
SPLIT(1) BSD General Commands Manual SPLIT(1)NAME
split -- split a file into pieces
SYNOPSIS
split [-a suffix_length] [-b byte_count[k|m] | -l line_count -n chunk_count] [file [name]]
DESCRIPTION
The split utility reads the given file and breaks it up into files of 1000 lines each. If file is a single dash or absent, split reads from
the standard input. file itself is not altered.
The options are as follows:
-a Use suffix_length letters to form the suffix of the file name.
-b Create smaller files byte_count bytes in length. If 'k' is appended to the number, the file is split into byte_count kilobyte
pieces. If 'm' is appended to the number, the file is split into byte_count megabyte pieces.
-l Create smaller files line_count lines in length.
-n Split file into chunk_count smaller files.
If additional arguments are specified, the first is used as the name of the input file which is to be split. If a second additional argument
is specified, it is used as a prefix for the names of the files into which the file is split. In this case, each file into which the file is
split is named by the prefix followed by a lexically ordered suffix using suffix_length characters in the range ``a-z''. If -a is not speci-
fied, two letters are used as the suffix.
If the name argument is not specified, 'x' is used.
STANDARDS
The split utility conforms to IEEE Std 1003.1-2001 (``POSIX.1'').
HISTORY
A split command appeared in Version 6 AT&T UNIX.
The -a option was introduced in NetBSD 2.0. Before that, if name was not specified, split would vary the first letter of the filename to
increase the number of possible output files. The -a option makes this unnecessary.
BSD May 28, 2007 BSD