11-04-2007
rtls0 works
im back. i was just looking through my dev dir and found rtls and rtls0. rtls had nothing in it but rtls0 shows my network card when i plumb it. when i disconnect my cable the data in rtls0 goes away. when it was up and i did a ifconfig -a it showed rtls0 and the loopback. also, my machine isnt directly connected to the internet. i have a router. i forgot what i did but it said something about hop 000/8 - something route not directly connected, so im thinkin i need to configure it with my router.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I running HPUX 11.0,
Netscape gives me an error "Unable to locate Server" when using a www.something.com address.
If I use an IP address I get past the router and onto the Internet.
My workstation can get to the Router @ 192.168.0.1 and also it's local APACHE server.
I have DHCP enabled... (8 Replies)
Discussion started by: johnalt
8 Replies
2. Solaris
ive installed a fresh copy of solaris 10 on a E3500 Server machine, i gave it a static IP address , 192.168.1.15 its a test server in our office (small office) we are using LINKSYS as our internet router and DHCP as well .. its IP is 192.168.1.1 and ive added this IP as Default route on the server... (9 Replies)
Discussion started by: mduweik
9 Replies
3. Solaris
Hi,
I am new to Solaris just migrating from Windows XP.
I want to connect to internet but I have problem with configuration.
My ISP has provided me a router.I get internet connection through DHCP.
I don't know any proxy or subnetmask or any IP address that requires during configuration of... (1 Reply)
Discussion started by: pappu2008
1 Replies
4. Solaris
Hi I installed solaris developer edition 1/08 today.I want to connect to Broadband internet through my ADSL 2+ Modem/Router with a username and password.
plz help in this case,I am new to sun solaris:confused:
the modem itself is a router it worked well on ubuntu and red hat (3 Replies)
Discussion started by: santugvd
3 Replies
5. Linux
HI,
Am using GPRS ( MOB # 3230 ) internet connection in windows
Hw to use internet r connect in linux.. ( Red Hat Linux Ver.10 )
Please help me..
Thanks in adv.. (1 Reply)
Discussion started by: bharath raja
1 Replies
6. UNIX for Dummies Questions & Answers
I recently installed solaris 10 on a seperate hard disk in my desktop pc. My first hard disk is running windows xp.
I am totally new to solaris. Please help me to connect to the internet through solaris 10. I read a few threads, and re-installed solaris 10 by giving 'Yes' to the question that... (1 Reply)
Discussion started by: hari86av
1 Replies
7. Solaris
Dear freinds...
I downloaded solaris for x86 and was able to configure the lan correctly.. I can ping and share with other destops through lan... but still I can't connect to internet ? can you please help..
I put my default gateway which is 192.168.1.1 to /etc/defaultrouter but with no use..... (13 Replies)
Discussion started by: yahyaaa
13 Replies
8. Linux
Hi,
Can someone guide me regarding how to connect to internet.
what are steps?
Thanks in advance (2 Replies)
Discussion started by: naren nandale
2 Replies
9. Red Hat
What all is required so that I can use internet on my Linux OS
My OS: Red Hat Fedora
version: 2.6
I have to connect via my Nokia cell phone via cable.
This way only I had been using internet on my Windows OS.
If any software is required to install on my UNIX for internet, then I don't... (1 Reply)
Discussion started by: ravisingh
1 Replies
10. IP Networking
How to enable internet on my Linux OS
My OS: Red Hat Fedora
Release 9 (Sulphur)
version: 2.6
I have to connect via my Nokia cell phone via cable.
This way only I had been using internet on my Windows OS.
If any software is required to install on my UNIX for internet, then I don't have any. If... (14 Replies)
Discussion started by: ravisingh
14 Replies
GRE(4) BSD Kernel Interfaces Manual GRE(4)
NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO
gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD
November 7, 2014 BSD