10-09-2007
if you are on a solaris 10 system also insert the ip settings in /etc/inet/ipnodes. you only have to do that on pre 10 8/07 versions of solaris.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
HELP!! How do you change the network setting from auto-duplex to 100 Base T Full Duplex in Red HaT? (1 Reply)
Discussion started by: johnlong
1 Replies
2. UNIX for Dummies Questions & Answers
Total newbie here!!
How do I view and alter network settings (ip address, subnet mask and default gateway) in UNIX?
Thanks in advance.. (3 Replies)
Discussion started by: ZappaDub
3 Replies
3. Linux
I've been looking for documentation on how to stop this behavior. I have two nics in my system.
eth0: configured manually and as a dhcp server for the local network
eth1: configured w/ dhcp enabled connected to router
dns server addresses keep getting reset every few minutes. i suspect... (0 Replies)
Discussion started by: rbetzen
0 Replies
4. IP Networking
hello i have a ubuntu ssh server that i can acess from any of my comnputers but only if they are on the same wireless network as the server. i tested trhis my tehtehring my samsung blackjack to my windows partition and installing openssh to windows it works when windows is on the wireless but no... (1 Reply)
Discussion started by: old noob
1 Replies
5. HP-UX
Hello everyone..
While printing through command line, we can set printing option with -o <lanscape/portrait> to print file in required mode.
But i want to know is there any way we can set this as default behaviour for this printer?
After configuration any script we can modify for this... (0 Replies)
Discussion started by: laxmikant
0 Replies
6. UNIX for Dummies Questions & Answers
Hello Unix Gurus Who I Hope Reads This,
I have quasi-inherited control over a Linux cluster at a university research lab. The post-doc that set it up is gone, and the person in charge of administering the cluster doesn't know a ton about Linux. Amongst other things, I want to use the cluster... (0 Replies)
Discussion started by: mbl
0 Replies
7. Solaris
Hi
i have created a solaris zone but have not yet connected any network cables for this new zone,
can i set the zone up without running the command 'add net' and not adding an ip or physical interface?
i tried to add dummy internet settings and get this
zonecfg:coddr> add net... (4 Replies)
Discussion started by: newbiesolaris10
4 Replies
8. Shell Programming and Scripting
Hello, Newbie question on scripting - I'm looking to create a simple script that will work on RHEL5 that will adjust the network settings: ip address, default gateway, and subnet mask. If anything else needs to be done (service network stop / start) or should be done to make settings active - I... (4 Replies)
Discussion started by: rojizo
4 Replies
9. UNIX for Dummies Questions & Answers
Hi,
I have inherited a Motorola System V R32V3.2 system. The system works fine, but we need to change the network settings. I've changed the IP address successfully, however I'm lost on the gateway and subnet mask. I've changed the default gateway using route -g10.0.8.1, but it changes back to... (7 Replies)
Discussion started by: Tilmar
7 Replies
LEARN ABOUT LINUX
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)