09-26-2007
alternative
if you haven't got to graphic kart you must connect to serial port
other macine hyper terminal
10 More Discussions You Might Find Interesting
1. SCO
Can i change the password on the SCO GUI interface login page and if so how?
When I try to login it just goes right back to the login screen. If anyone has any suggestions, please reply. :confused: (3 Replies)
Discussion started by: qphillips
3 Replies
2. Linux
hi
iam installed mandriva spring 2009
iam unble to login into gui using root
how to enable it
where the settings are stored (5 Replies)
Discussion started by: seshumohan
5 Replies
3. Solaris
I have 2 queries:
1.how do we monitor failed GUI logins...? I think the /var/adm/loginlog will log
only failed logins happened at /dev/console and virtual terminals..
2.How to use cron scheduler to display a message when a user is working in GUI Terminal window irrespective of in which... (1 Reply)
Discussion started by: saagar
1 Replies
4. UNIX for Advanced & Expert Users
Hi,
When I installed Ubuntu on my laptop, I had chosen "automatic login" . So i was not asked ofr username and password everytime I switched on. I later wanted to change the settings. So I went to systems-->administration-->login window-->security. There I disabled automatic login and I reboot the... (3 Replies)
Discussion started by: vishwamitra
3 Replies
5. Solaris
I have a Sun Ultra 45 that was working perfectly until i upgraded it to Update 9 with a zfs filesystem. The box is sparc based and has an internal video card. When i boot it up, i receive an X server error and, while checking /var/dt/Xerrors, the following message is displayed
Fatal server... (9 Replies)
Discussion started by: goose25
9 Replies
6. Fedora
Hi all,
I am able to login via putty to a fedora 10 workstation.
But when i try to login via physical screen connected to workstation, it just gives me a blank screen and i cant see any options to enter username and passwd. How do i get the physical GUI to work.
$ who -r
... (4 Replies)
Discussion started by: lramsb4u
4 Replies
7. AIX
If I login to one of our AIX 6.1 servers using SSH via PuTTY and I issue the who -a or w command I cannot see my session, although if I login via TELNET I can.
Why is this?
SSH:
root#> who
root#> w
08:06PM up 40 days, 27 mins, 0 users, load average: 0.05, 0.12, 0.14
User tty login@ idle... (1 Reply)
Discussion started by: deepinsight
1 Replies
8. Solaris
Solaris machine is at # prompt not able to login in GUI mode :
I want to login solaris server in GUI mode from # prompt.
---------- Post updated 12-30-11 at 11:36 AM ---------- Previous update was 12-29-11 at 02:23 PM ----------
Hi,
Please send me some guidelines regarding this....
as... (2 Replies)
Discussion started by: sunray
2 Replies
9. UNIX for Dummies Questions & Answers
I am not too new with linux. Since I installed a new version (2011) of Mandriva, I am unable to login via the gui (I'm currently using the live version of the same dvd free with Linux Format mag). I can login from a console as it has picked up the previous version's /home, but when I try to login... (2 Replies)
Discussion started by: richardmellersh
2 Replies
10. Shell Programming and Scripting
hii all,
I am unable to login into GUI mode in solaris 10. It is only prompting me to command mode credentials not going further to GUI mode.. Please help..
Thanks & regards,
Bhagi (3 Replies)
Discussion started by: bhargav90
3 Replies
LEARN ABOUT HPUX
lcpu_attr
lcpu_attr(5) File Formats Manual lcpu_attr(5)
NAME
lcpu_attr - dynamically enable or disable LCPU attribute of the default processor set
VALUES
Fail Safe
Default
the LCPU attribute of the default processor set is disabled
Allowed values
or
DESCRIPTION
This tunable dynamically enables or disables the logical processor (LCPU) attribute in the default processor set. On systems supporting
hyper-threading technology, each hyper-thread is represented as an LCPU.
When the LCPU attribute is enabled, the processor cores in the default processor have hyper-threading enabled. If the LCPU attribute is
disabled, the physical processors in the default processor set behave as single threaded processor cores.
See pset_setattr(2) for information about managing the LCPU attribute in processor sets other than the default processor set.
Who Is Expected to Change This Tunable?
System administrators that wish to change hyper-threading ability in the default processor set.
Restrictions on Changing
The tunable has no effect on platforms that do not have hyper-threading capability or systems with hyper-threading disabled at the firmware
level. On systems that support hyper-threading, the firmware feature must be enabled to dynamically enable/disable the LCPU attribute in
the default processor set.
When Should the Tunable Be Turned On?
The tunable should be turned on to enable the LCPU attribute in the default processor set to take advantage of hyper-threading. If the
applications running on the system see performance benefits, the LCPU attribute should remain enabled.
What Are the Side Effects of Turning the Tunable On?
Some workloads may experience performance degradation when the LCPU attribute is enabled.
When Should the Tunable Be Turned Off?
Some applications may experience performance degradation or may not see any performance benefits from using hyper-threading. In this case,
this tunable should be turned off.
What Are the Side Effects of Turning the Tunable Off?
With LCPU turned off, applications may not take advantage of hyper-threading.
What Other Tunables Should Be Changed at the Same Time?
None.
WARNINGS
All HP-UX kernel tunable parameters are release specific. This parameter may be removed or have its meaning changed in future releases of
HP-UX.
Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation,
some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun-
able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was
factory installed on your system, see at
AUTHOR
was developed by HP.
SEE ALSO
psrset(1M), pset_assign(2), pset_bind(2), pset_create(2), pset_ctl(2), pset_destroy(2), privgrp(4).
Tunable Kernel Parameters lcpu_attr(5)