Sponsored Content
Operating Systems AIX Using AIX HACMP and NFS together Post 302134684 by chongkls77 on Sunday 2nd of September 2007 11:40:31 PM
Old 09-03-2007
Using AIX HACMP and NFS together

Hi,

need advice on this.

Is it possible to assign a mountpoint from a SAN storage to server1 & server2.
Use NFS to the same mountpoint from server2 so that concurrent access is allowed.
Can this setup be used together with HACMP?
If server1 crash, the mountpoint resource will swing to server2, will it automatically remove the NFS and server2 take over the mountpoint resource and become active.

Simpler approach is to use PFSS?

Any ideas?

Regards
Solo
 

10 More Discussions You Might Find Interesting

1. AIX

AIX 6.1 and NFS problem after HACMP config

Hello folks, I am facing a problem with NFS after doing the HACMP configuration Issue : The showmount -e pr2serv at pr1serv ,it is only showing 1 mount exported /oracle , instead of showing all 7 as per /etc/exports file. issue : while mounting /oracle at pr1serv getting permission... (8 Replies)
Discussion started by: filosophizer
8 Replies

2. AIX

HACMP 5.4 with AIX 5300-10 not working

I have two IBM_9110-51A boxes OS - fresh installs 5764-G03 TL 5300-10-00 disks dated 5/2009 HACMP - fresh installs HACMP for AIX 5L Base V5.4 5765-F62 dated 7/2006 Bottom line for smit output attempting 2 node cluster config ... (2 Replies)
Discussion started by: DrKillPatient
2 Replies

3. AIX

NFS won't work till I start HACMP

Hi, My NFS does not work till I start HACMP. The NFS service is indeed started when server starts. But it is not in active state, when I use lssrc to check NFS services' status I find they are all in inoperative status. But after I start HACMP (smitty clstart), all NFS services become active... (4 Replies)
Discussion started by: qiulang
4 Replies

4. AIX

AIX HACMP Active/Passive Config

I have a HACMP 6.1 configured in a active/passive. I have 1 NIC with 3 IP address on (Boot, Persistent and Service ) . All address are routable. One of the application on the HA cluster is also using Boot Ip to send application data. Question : Since all the traffic is passing thru the same... (3 Replies)
Discussion started by: mk8570
3 Replies

5. UNIX for Advanced & Expert Users

HACMP version for AIX 6.1

Hello. We are using AIX 5.3 with HACMP 5.4.1. At this moment AIX and clustering are using 2 servers. A third server is added. It does not seem to work with HACMP. Are there any controle checks? Thank you if you could help. Regards, Ynze van Aken Netherlands (0 Replies)
Discussion started by: yvanaken
0 Replies

6. AIX

HACMP, NFS cross-mount problem. Can not move resource group

Hi, I'm new to HACMP. Currently I setup a cluster with nfs cross-mount follow this guide: kristijan.org NFS cross-mounts in PowerHA/HACMPMy cluster has two nodes: erp01 and erp02. I'm using nfs4 with filesystem for nfs is: /sapnfs Cluster start without problems. But I cannnot move RG (with... (3 Replies)
Discussion started by: giobuon
3 Replies

7. AIX

Hacmp for aix 5.3

Hi where from i can get hacmp for studying pupose (trial ). I have AIX 5.3 TL 7 i googled. i didnt get any link. Please suggest. (1 Reply)
Discussion started by: sunnybee
1 Replies

8. AIX

HACMP and NFS client

Hi all, I know there are topics regarding this but didn't found the answer. I have two node HACMP cluster and the application that runs there relies on some NFS mount. The NFS server is some 3rd box that have nothing to do with the cluster. How can I mount the NFS shares only on the active... (5 Replies)
Discussion started by: emoubi
5 Replies

9. AIX

How to check if HACMP is running on AIX node?

Hello AIX experts, I have few queries and appreciate if you could help me with them. 1. How to check if HACMP (or any other AIX OS cluster) is installed 2. How to check if HACMP (or any other AIX OS cluster) is running 3. how to check which Oracle DB instance is running on it 4. how to... (1 Reply)
Discussion started by: prvnrk
1 Replies

10. AIX

AIX NFS Server and NFS Client

Hi 2 ALL, try to run NFS Server in AIX 7.1 : 1. Step by step on NFS Server node mkdir /tmp/test chgrp staff /tmp/test chmod 775 /tmp/test-- create export directory (fs) mknfsexp -d /tmp/test -t ro exportfs -va show mount -e :/# exportfs -av exports: 1831-187 re-exported /tmp/test... (4 Replies)
Discussion started by: penchev
4 Replies
FUSEDAV(1)						      General Commands Manual							FUSEDAV(1)

NAME
fusedav - mount WebDAV shares SYNOPSIS
fusedav [-hDL] [-t secs] [-u username] [-p password] [-o options] URL mountpoint DESCRIPTION
fusedav is a userspace filesystem driver that allows you to mount WebDAV shares. This way you can transparently edit and manage files on a remote server. As long as the fusedav process is running, the WebDAV share located at URL is accessible under mountpoint. If username and password are required and you did not specify them on the command line you will be prompted as soon as you are trying to access the mounted share. OPTIONS
-h Show summary of options. -D Enable debug mode. -L Lock the repository during mount. (Not properly supported on all servers, hence not enabled by default.) -t secs Set lock timeout to secs seconds. -u username Use username for authentication if required. -p password Use password for authentication if required. -o options Pass options as additional mount options to FUSE. URL Location of the WebDAV share. mountpoint Local mountpoint of the WebDAV share. AUTHOR
fusedav was written by Lennart Poettering <mzshfrqni (at) 0pointer (dot) de>. This manual page was written by Sebastian Harl <tokkee@debian.org>, for the Debian project (but may be used by others). August 24, 2006 FUSEDAV(1)
All times are GMT -4. The time now is 08:36 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy