Sponsored Content
Top Forums UNIX for Dummies Questions & Answers How to assign virtual address?. Post 302132464 by joerg on Friday 17th of August 2007 04:30:51 AM
Old 08-17-2007
Use ifconfig:
ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.10.8 netmask ffffff00 broadcast 192.168.10.255
ether 0:14:4f:e:87:a4
bash-3.00# ifconfig bge0:1 plumb
bash-3.00# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 192.168.10.8 netmask ffffff00 broadcast 192.168.10.255
ether 0:14:4f:e:87:a4
bge0:1: flags=1000842<BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 0.0.0.0 netmask 0



Now you can change with ifconfig the ip netmask and set the bge0:1 UP
Thats all!
Best regards joerg
 

10 More Discussions You Might Find Interesting

1. Solaris

How to assign multicast IP address

How can I assign multicast ip address to my Sun server. I need this configuration to set up weblogic in cluster mode. This setup needs a multicast IP address where the managed servers can broadcast their heartbeats. Thanks (0 Replies)
Discussion started by: krishan
0 Replies

2. IP Networking

Virtual IP address

We currently have a Solaris Wks that is being used as an "ftp server" and it routinely accepts data each night that if ftp'd to it from off site. In the event that this "ftp server" should fail (crash, die, whatever) we would like to have an automatic fail over to a second Solaris Wks as the "ftp... (2 Replies)
Discussion started by: kanejm
2 Replies

3. AIX

Virtual IP address in HACMP

I am new to HACMP V5.4 in AIX5.3.Please let me know how to get the virtual IP address configured for a HACMP cluster. Is this the correct way to identify it? If i give ifconfig -a the first ip address displayed is the real address of the host.So the other one can be VIP. Thanks in Advance (3 Replies)
Discussion started by: guru13
3 Replies

4. Solaris

How to assign MAC address to N/W interface in solaris

I m having interface ce0 ce1 and its sub interfaces for that. I want to give MAC addresses for the same. How will I assign it. Please give solution for the same (4 Replies)
Discussion started by: sunray
4 Replies

5. IP Networking

assign mac address for virtual interface eth1:0

Hi , by default the physical interface (eth1) and virtual interface eth1:0 will be having same mac address, is there any way we can assign separate mac addresses for both the interfaces. would some one help me out in this. Thanks Gopi (1 Reply)
Discussion started by: Gopi Krishna P
1 Replies

6. Solaris

How to assign static ip address to the server having solaris 10. i.e. nge0

hi, how to assign static ip address to the server having solaris 10. assign static ip to nge0 which will sustain across reboots which will include all settings including gateway setting etc.. (2 Replies)
Discussion started by: pankajd
2 Replies

7. UNIX for Dummies Questions & Answers

What would the physical address be for virtual address?

Hi guys, I got one problem which I definetily no idea. What would the physical address be for virtual address? 1) 2ABC 2) 3F4B Here is the page table:see attached Thank you sos sososososso much!! (0 Replies)
Discussion started by: lemon_06
0 Replies

8. Solaris

i want to set ip address to a virtual machine

hi all i want to set ip address to a vitrual machine i am using following command. but it is not ifconfig -a command output. what is wrong i dont know bash# ifconfig interfacename plumb bash# ifconfig interfacename auto-dhcp Please use code tags next time for your code and data. (4 Replies)
Discussion started by: nikhil kasar
4 Replies

9. IP Networking

Virtual Adapter MAC address..

Hi, I just want to know whether two MAC address can exist in a adapter.. I mean one there will be mandatory one And another as user defined one.. Any replies will be more helpful.. Please help.. :wall: (0 Replies)
Discussion started by: Priya Amaresh
0 Replies

10. IP Networking

IPv6 address block assign/associate with an interface

Hello all, I am trying to receive (tcp/udp/sctp) traffic from all IPs and, eventually, all ports of an IPv6 address block using as few sockets as possible short of implementing my own network stack. One possible solution was to associate an IP block to an interface then bind to that... (6 Replies)
Discussion started by: redwil
6 Replies
svatophys(9r)															     svatophys(9r)

NAME
svatophys - General: Converts a system virtual address to a physical address SYNOPSIS
kern_return_t svatophys( vm_offset_t kern_addr, vm_offset_t *phys_addr ); ARGUMENTS
Specifies the kernel virtual address. Specifies a pointer to the physical address to be filled in. DESCRIPTION
The svatophys routine converts a system virtual address to the corresponding physical address. All address and data structure manipulation done within the kernel is performed using system virtual addresses. Typically, system virtual addresses are a means of mapping physical memory and I/O space, which often consists of device registers and DMA buffers. In contrast to this, devices are usually unaware of any virtual addressing and for this reason use physical addresses. You use the svatophys routine to perform this address translation. As an example of where you can use this address translation, a disk device driver can use DMA buffers to transfer blocks of data to the disk (for the case of a write operation). The data to be written to disk is present in system memory at a system virtual address known to the driver. To initiate the DMA operation, the disk driver can set up a command packet to specify a write operation to the underlying disk controller hardware. This write command packet contains (among other things) the location of the DMA buffer as a physical address and the length of the buffer. Here, the driver calls the svatophys routine to translate the system virtual address of the DMA buffer to a physical address in the command packet issued to the disk driver. RETURN VALUES
The svatophys routine returns the following: The address translation has been completed successfully. Unable to perform address transla- tion. This value indicates that the address specified by the kern_addr argument is not a valid kernel or system virtual address. svatophys(9r)
All times are GMT -4. The time now is 07:39 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy