I wish to seach a Dir for a specific file, once the file is found i will perform additional logic. If the file is not found within two hours, i would like to exit.
Logically, I'm looking for the best way to approach this
Thanks for any assistance in advance.
Note: I'm using a C shell and... (2 Replies)
I want to create an automated script which is called by another maually executed script.
The condition is that the no one should be able to manually execute the automated script.
The automated script can be on the same machine or it can be on a remote machine.
Can any one suggest a check in the... (1 Reply)
Hi
Can anyone please help with the following script I need - .ksh preferably?
I have external disks attached to a system that I have to label and then run the dd command on all external disk found.
I have kicked off the dd command as follows manually to see what its output is like first... (1 Reply)
hi guys ..newbie here i would like to create a simple script tat will detect wether the machine has IP or not ...
but it seems that my script doesnt really work it kept rebooting...
i set this script during boot so that it will check else it will reboot
it a shell script thou...
... (5 Replies)
I have a local linux machine in which the files are dumped by a remote ubuntu server. If the process in remote server has any problem then empty files are created in local machine. Is there any way using perl script to check if the empty files are being created and delete them and then run a shell... (2 Replies)
Hi,
I am a unix newbie. I need to write a script to check wheteher another script is still running. If it is, then sleep for 30m and then check again if the script is running. If the script has stopped running then, I need to come out of the loop.
I am using RHEL 5.2 (2 Replies)
Hi guys,
I am sending the script i created..plzzz check it correct if any mistakes...:).
Plz reply early by today..
here i want to find the files based on date , if files are avaliable i want to send a mail to the user. here there are a total of 43 files. they are constant.
Here is... (0 Replies)
hi guys
we've had nagios spewing false alarm (for the umpteenth time) and finally the customer had enough so they're starting to question nagios. we had the check interval increased from 5 minutes to 2 minutes, but that's just temporary solution. I'm thinking of implementing a script on the... (8 Replies)
Hello,
I am not efficient in script, so need some help to create a small script.
I have file, which have list of all IPs. All those IPs can be connected from a gateway server with "sudo ssh 10.63.xx.xx". We do not have reverse lookup for IPs, so I want script to login to each server, return... (1 Reply)
SunOS -s 5.10 Generic_147440-04 sun4u sparc SUNW,SPARC-Enterprise
Hi,
on one system there are folders which are being created based on today's date
/data/CDR/sswitch_roa/voice/bkup/<yyyymmdd> (e.g /data/CDR/sswitch_roa/voice/bkup/20180620 – is the path for today’s... (1 Reply)
Discussion started by: roshanbi
1 Replies
LEARN ABOUT DEBIAN
bestups
BESTUPS(8) NUT Manual BESTUPS(8)NAME
bestups - Driver for Best Power / SOLA (Phoenixtec protocol) UPS equipment
NOTE
This man page only documents the hardware-specific features of the bestups driver. For information about the core driver, see nutupsdrv(8).
SUPPORTED HARDWARE
bestups was designed to monitor Best Power UPS hardware like the Fortress, Fortress Telecom, Axxium Rackmount and Patriot Pro. It also
recognizes and supports SOLA units such as the 325, 520 and 620. In addition, the Best 610 is supported using the 'ID' option.
Other UPS hardware using the Phoenixtec protocol should also work, but they will generate a warning since their battery information is not
known.
This driver does not support some older Best/SOLA units.
EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5):
nombattvolt=num
Override the battery float voltage which is normally determined by asking the hardware. This is useful if your UPS constantly reports
battery.charge values just below 100% even when it's completely charged.
If you have this problem, set this to whatever battery.voltage reports when the UPS is known to be completely charged with a good
battery.
The author's Best Fortress 750 uses nombattvolt=27.4.
battvoltmult=num
Multiply the reported battery voltage by this number. Some devices report only a fraction of the total battery voltage.
For example, the SOLA 610 700VA UPS (with a 24V battery) reports the single cell voltage (about 2.27V when fully charged). In this
particular case you can set battvoltmult = 12 in ups.conf(8) to fix this.
ID=string
Set the Identification response string. This should only be used with hardware that supports the Phoenixtec protocol status inquiry
commands, but not the "ID" command, such as the Best/SOLA 610. Format of the ID string is: AAA,BBBB,CCC,DDD,EE.E,FF.F
AAA is the three-character identification for the UPS model.
BBBB is the output power in VA (volt amperes). B is an integer number ranging from 0 to 9.
CCC is the Nominal Input Voltage. C is an integer number ranging from 0 to 9. The unit is Volts AC.
DDD is the Nominal Output Voltage. D is an integer number ranging from 0 to 9. The unit is Volts AC.
EE.E is the Battery Voltage that will cause the UPS to shut itself off. E is an integer number ranging from 0 to 9. Then unit is Volts
DC and a decimal point is present.
FF.F or FFF.F is the Battery Voltage at full charge. F is an integer number ranging from 0 to 9. Then unit is Volts DC. Typically, for
700VA, 1KVA and 1.5KVA units, the format is FF.F. For 2KVA and 3KVA units, the format is FFF.F.
Example: a Best 610 1.5KVA unit would use the string "610,1500,120,120,10.0,48.0".
BUGS
The battery charge percentage value (in battery.charge) is derived from the voltage data that the UPS returns, since the UPS doesn't return
that value directly. On some hardware, the charge will remain at 100% for a long time and then drops quickly shortly before the battery
runs out. You can confirm from the battery.voltage readings that this is a problem with the UPS and not this driver.
Similarly, the float from the charger in some models forces the battery charge percentage back up to 100% immedately after the UPS goes
back on-line, so you can't tell when it is really recharged.
Finally, some models give one value for the battery's nominal voltage and yet actually have a nominal voltage slightly below that. This
leads to things such as the perpetual 98.7% charge on the author's Fortress 750, even when it's been charging for weeks. You can use
nombattvolt= in ups.conf(8) to fix this.
AUTHOR
Russell Kroll, Jason White
SEE ALSO
The core driver:
nutupsdrv(8)
Internet resources:
The NUT (Network UPS Tools) home page: http://www.networkupstools.org/
Network UPS Tools 05/21/2012 BESTUPS(8)