Mail::SpamAssassin::Plugin::SPF(3pm)			User Contributed Perl Documentation		      Mail::SpamAssassin::Plugin::SPF(3pm)

NAME

       Mail::SpamAssassin::Plugin::SPF - perform SPF verification tests

SYNOPSIS

	 loadplugin	Mail::SpamAssassin::Plugin::SPF

DESCRIPTION

       This plugin checks a message against Sender Policy Framework (SPF) records published by the domain owners in DNS to fight email address
       forgery and make it easier to identify spams.

USER SETTINGS

       whitelist_from_spf user@example.com
	   Works similarly to whitelist_from, except that in addition to matching a sender address, a check against the domain's SPF record must
	   pass.  The first parameter is an address to whitelist, and the second is a string to match the relay's rDNS.

	   Just like whitelist_from, multiple addresses per line, separated by spaces, are OK. Multiple "whitelist_from_spf" lines are also OK.

	   The headers checked for whitelist_from_spf addresses are the same headers used for SPF checks (Envelope-From, Return-Path, X-Envelope-
	   From, etc).

	   Since this whitelist requires an SPF check to be made, network tests must be enabled. It is also required that your trust path be
	   correctly configured.  See the section on "trusted_networks" for more info on trust paths.

	   e.g.

	     whitelist_from_spf joe@example.com fred@example.com
	     whitelist_from_spf *@example.com

       def_whitelist_from_spf user@example.com
	   Same as "whitelist_from_spf", but used for the default whitelist entries in the SpamAssassin distribution.  The whitelist score is
	   lower, because these are often targets for spammer spoofing.

ADMINISTRATOR OPTIONS

       spf_timeout n	   (default: 5)
	   How many seconds to wait for an SPF query to complete, before scanning continues without the SPF result.

       do_not_use_mail_spf (0|1)	  (default: 0)
	   By default the plugin will try to use the Mail::SPF module for SPF checks if it can be loaded.  If Mail::SPF cannot be used the plugin
	   will fall back to using the legacy Mail::SPF::Query module if it can be loaded.

	   Use this option to stop the plugin from using Mail::SPF and cause it to try to use Mail::SPF::Query instead.

       do_not_use_mail_spf_query (0|1)	  (default: 0)
	   As above, but instead stop the plugin from trying to use Mail::SPF::Query and cause it to only try to use Mail::SPF.

       ignore_received_spf_header (0|1)   (default: 0)
	   By default, to avoid unnecessary DNS lookups, the plugin will try to use the SPF results found in any "Received-SPF" headers it finds
	   in the message that could only have been added by an internal relay.

	   Set this option to 1 to ignore any "Received-SPF" headers present and to have the plugin perform the SPF check itself.

	   Note that unless the plugin finds an "identity=helo", or some unsupported identity, it will assume that the result is a mfrom SPF check
	   result.  The only identities supported are "mfrom", "mailfrom" and "helo".

       use_newest_received_spf_header (0|1)    (default: 0)
	   By default, when using "Received-SPF" headers, the plugin will attempt to use the oldest (bottom most) "Received-SPF" headers, that
	   were added by internal relays, that it can parse results from since they are the most likely to be accurate.  This is done so that if
	   you have an incoming mail setup where one of your primary MXes doesn't know about a secondary MX (or your MXes don't know about some
	   sort of forwarding relay that SA considers trusted+internal) but SA is aware of the actual domain boundary (internal_networks setting)
	   SA will use the results that are most accurate.

	   Use this option to start with the newest (top most) "Received-SPF" headers, working downwards until results are successfully parsed.

perl v5.14.2							    2011-06-06				      Mail::SpamAssassin::Plugin::SPF(3pm)