Sponsored Content
Operating Systems Solaris Dual IP configuration with two different network card Post 302127991 by pressy on Friday 20th of July 2007 02:12:30 PM
Old 07-20-2007
IPMP groups are based on ICMP-targets to test the network connection. if you haven't specified any target with host-routes, the mpathd will try to ping the defaultrouter. if you cannot ping your gateway or haven't set one the interfaces in the group will fail...

regards
- PRESSY

(see the info doc on sunsolve 70062, but you will need a contract to view it)
 

10 More Discussions You Might Find Interesting

1. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the... (1 Reply)
Discussion started by: cparks
1 Replies

2. UNIX for Dummies Questions & Answers

Sound Card configuration

Hie, Im using Linux Kernel 2.2.16-22 (Linux Ver7.0), My problem is My sound Card is not detected and configured properly, i tried many ways but still cant configured it out. Heres my detail problem. Whenever i tried to configure my sound card which i newly purchased ( Creative Vibra 128 Audio... (2 Replies)
Discussion started by: killerserv
2 Replies

3. UNIX for Advanced & Expert Users

redhat 7.2 dual head video card

HI. i have two monitor and two video card in one system, i want use both of the monitor, i am currently using redhat 7.2 and solaris 8, i was wondering if someone can help me set my system as a dual monitor, basically it called dual head in redhat but i dont' know what it called in sun. Im tring... (4 Replies)
Discussion started by: souldier
4 Replies

4. UNIX for Dummies Questions & Answers

Dual network ports

Hey all, I got a Ultra 60 and I'm going to put a quad fast ethernet card into it, also I have a NAS with dual ethernet ports. I'm going to setup the Ultra 60 as a gateway to the NAS. Is it possible to setup 2 ports on the quad fast ethernet card to talk to the 2 ports on the NAS? Both... (2 Replies)
Discussion started by: merlin
2 Replies

5. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of... (3 Replies)
Discussion started by: The Fridgerator
3 Replies

6. SCO

speciliax card configuration

dear all i configured pci speciliax card in sco open server 5.0.5 but i only getting cursor prompt in terminal side my terminal is vt100 pls give the quries for configure terminal and speciliax card regards jeevaraj (0 Replies)
Discussion started by: jeevaraj
0 Replies

7. UNIX Desktop Questions & Answers

Dual monitor for Intel 82915G & ATI Rage 128 card on FC6, Dell Optiplex Gx520

I want to setup dual monitor for the Dell Optiplex Gx520 computer. The motherboard has an Intel Corporation 82915G Integrated Graphics Controller. Then I add an ATI Rage 128 video card. The dual monitor work on Windows 2000 with the Intel chip as the primary screen and the ATI chip... (0 Replies)
Discussion started by: TsanChung
0 Replies

8. Solaris

quad card configuration

Hi Group, I Have just installed quad card in my V440 machine, I am facing problem I cn just ping its ce0 card only rest of the cards are not ping able, here is details of my machine. ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 ... (2 Replies)
Discussion started by: sameergrover
2 Replies

9. Hardware

FAQ, support multiple monitor 3 or 4 using dual video card SLI or Crossfire

Hi, I would like to ask if someone has knowlodge or perhaps own/experience this kind of a machine, Im buying a desktop with a plan of having multiple monitor 3 or 4,now my question is, i want to used the sli or crossfire config with each video card has 2 dvi or vga connector, does this 2... (0 Replies)
Discussion started by: jao_madn
0 Replies

10. UNIX for Beginners Questions & Answers

Want to dual boot windows/Linux on a ssd/hdd configuration

I have a small ssd (240 GB) and a 1TB hdd. I want to use the ssd to store anything related to Windows (os and other stuff like games) and also the linux bootloader (so linux boots faster). And I want my hdd space to be for linux stuff (like the fedora os, linux packages, etc). Can you help me do... (1 Reply)
Discussion started by: mafiaskafia
1 Replies
if_mpadm(1M)						  System Administration Commands					      if_mpadm(1M)

NAME
if_mpadm - administer interfaces in an IP multipathing group SYNOPSIS
if_mpadm -d | -r ifname DESCRIPTION
The if_mpadm utility administers IP interfaces that are part of an IP Multipathing (IPMP) group. Currently, administration is limited to offlining IP interfaces and undoing previous offline operations. When an IP interface is taken offline, all IP data traffic that was flowing over the IP interface is moved to another IP interface in the IPMP group. In addition, all UP IP addresses hosted on the IP interface are brought down, causing in.mpathd(1M) to stop probe-based failure detection on the IP interface. As a result, an offline IP interface will not be used for any inbound or outbound IP traffic. Only IP inter- faces that are in an IPMP group may be brought offline. If the IP interface is the last functioning interface in the IPMP group, the off- line operation will fail. When an offline operation is undone, any IP addresses hosted on that IP interface are brought UP and will be considered by in.mpathd for probe-based failure detection. In addition, provided the IP interface is otherwise active (see in.mpathd(1M)), it will again be used to send and receive IP data traffic for the IPMP group. Note that not all offline operations can be undone. For instance, in.mpathd may have offlined an IP interface because its hardware address was not unique within its IPMP group. The ipmpstat utility can be used to determine why an IP interface is offline, identify which IP interfaces in a group are being used for inbound and outbound IP traffic, and more; see ipmpstat(1M). OPTIONS
The if_mpadm utility supports the following options: -d ifname Offline the IP interface specified by ifname. If ifname is not in an IPMP group, or the offline would cause the IPMP group to lose network connectivity, the operation will fail. -r ifname Undo a previous offline of the IP interface specified by ifname. If ifname is not offline, the operation will fail. EXAMPLES
Example 1 Offlining an IP Interface The following command offlines the IP interface under0, causing any IP packets that were being sent and received through it to be handled by another IP interface in its group. example% if_mpadm -d under0 Example 2 Undoing a Previous Offline Operation Use the following command to undo the operation in the previous example: example% if_mpdadm -r under0 ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ |Interface Stability |Unstable | +-----------------------------+-----------------------------+ SEE ALSO
ifconfig(1M), in.mpathd(1M), ipmpstat(1M), attributes(5) DIAGNOSTICS
cannot offline: no other functioning interfaces are in its IPMP group. Description: This message means that offlining the IP interface would leave the IPMP group without network connectivity. cannot offline: not a physical interface or not in an IPMP group Description: This means that the IP interface is not an underlying interface in an IPMP group, and therefore is not eligible to be offlined. SunOS 5.11 5 Jan 2009 if_mpadm(1M)
All times are GMT -4. The time now is 03:25 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy