07-01-2007
If tape drive is only used once in a while, you can always DLPAR the Ultra320 from one lpar to another.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Can anyone out there help me out? I'm trying to install a scsi tape back up on a sys running sco openserver 5.0.4. When I go through the steps for mkdev tape it seems like it works, but when I reboot I still don't see the tape. Also when it boots up I get a scsi bios not installed error. I've... (1 Reply)
Discussion started by: goatboy_tx
1 Replies
2. Solaris
Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy.
I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this... (4 Replies)
Discussion started by: Plain Person
4 Replies
3. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
4. SCO
I'm floundering here trying to locate a PCI-E 1x HBA that will support an external tape drive in SCO Openserver 6. I was unable to find anything that would work in the compatible hardware list and a call to Adaptec confirmed that PCI-X would've been a better option for the risers in the Dell 2950... (1 Reply)
Discussion started by: s_mal
1 Replies
5. AIX
Hello,
Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter.
It is similar to virtual scsi adapter.
In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Discussion started by: filosophizer
1 Replies
6. Hardware
I need to connect 80pin SCA Ultra320 SCSI hdd to 68pin.
There are rumors that some bad "passive" adapters with problematic termination can fry the HDD. The adapter we got is Assmann ABSCA-2. Hard drive is 'Fujitsu MAW3073NC'
Do we need to set any jumpers before turning it on?
We already had... (0 Replies)
Discussion started by: orange47
0 Replies
7. AIX
All
I am at a loss with a VIO server running ios 2.2.0.10-FP-24 SP-01. The VIO server is fitted with two 8Gb PCI Express Dual Port FC Adapters. However when I run the lsnports command only two of the adapter ports show as capable:
$ lsnports
name physloc ... (4 Replies)
Discussion started by: johnf
4 Replies
8. SCO
PCI-X was popular years ago, now it's not. Today's motherboards have PCIe slots, not PCI-X slots. I'm accustomed to using Adaptec, but I believe they've been bought out by ATTO Technology. Now ATTO has a product called PCI UL50 Dual Channel VHDCI Ultra320 SCSI PCIe card. So: does the SCO UNIX... (7 Replies)
Discussion started by: Transpower
7 Replies
9. SCO
OK group, it's been 12 years since I worked with SCO. I need some direction here:
SCO Openserver 5.07
I have a server with a bad motherboard. I have moved the SCSI adapter and hard drive to another computer. This new server has different hardware so I must install the chipset drivers for... (1 Reply)
Discussion started by: jscholz
1 Replies
10. HP-UX
I am trying to reload a RP4440 with 2x300gb disks and dual Port Network card, with HPUX 11.11 Sept 2003. When the os boots and and gets to the main menu to install HPUX or run recovery, it cannot find the disks or NIC.
At the OS prompt (after loading files), ioscan shows the Class ba, and shows... (0 Replies)
Discussion started by: mrmurdock
0 Replies
tz(4) Kernel Interfaces Manual tz(4)
Name
tz - SCSI magnetic tape interface
Syntax
VAX NCR 5380:
adapter uba0 at nexus?
controller scsi0 at uba0 csr 0x200c0080 vector szintr
tape tz0 at scsi0 drive 0
VAX DEC SII:
adapter ibus0 at nexus?
controller sii0 at ibus? vector sii_intr
tape tz0 at sii0 drive 0
RISC DEC SII:
adapter ibus0 at nexus?
controller sii0 at ibus? vector sii_intr
tape tz0 at sii0 drive 0
RISC DEC KZQ:
adapter uba0 at nexus?
controller kzq0 at ibus? csr 0761300vector sii_intr
tape tz0 at kzq0 drive 0
RISC NCR ASC:
adapter ibus0 at nexus?
controller asc0 at ibus? vector ascintr
tape tz0 at asc0 drive 0
Description
The SCSI tape driver provides a standard tape drive interface as described in This is a driver for any Digital SCSI tape device.
For the TZK10 QIC format tape drive, the densities supported are QIC-24 (read only) block size of 512 byte blocks, QIC-120, and QIC-150
read/write block size of 512 byte blocks, and QIC-320 read/write block size of 1024 byte blocks. With QIC format style tapes all reads and
writes must be in multiple of the block size. This is a requirement of fixed block tape drives because record boundaries are not pre-
served. The QIC densities are selected using the following special device names:
QIC-24 Fixed block size.
QIC-120 Fixed block size.
QIC-150 Fixed block size.
QIC-320 Fixed block size.
With all fixed block tape devices a of a file to the tape must be padded out. An example of this is a of which has a size of approximately
3800 bytes.
dd if=/etc/gettytab of=/dev/rmt0h bs=10k conv=sync
or
dd if=/etc/gettytab of=/dev/rmt0l bs=512 conv=sync
The option of pads the output to block size.
This driver also supports n-buffered reads and writes to the raw tape interface (used with streaming tape drives). See for further
details.
Tape Support
TZ30, TZK50, TLZ04, TSZ05, TKZ08, TZK10
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
Files
See Also
mtio(4), nbuf(4), SCSI(4), MAKEDEV(8), uerf(8), tapex(8)
Guide to the Error Logger
tz(4)