06-26-2007
What if you added the '-f inet6' to netstat? What is the output?
I'm not using AIX. Do you have utilities such as tcpdump available on your platform which is IPv6-enabled to verify that a UDP6 packet actually got sent with your UDP dig? I guess it could be due to misconfiguration of bind that it erroneously listened on IPv4.
What did you specify in the config for the "listen-on-v6" directive? If you want bind to listen on IPv6, you should have that.
9 More Discussions You Might Find Interesting
1. Solaris
hey guys, how to add soalris box as a microsoft DNS Client ?
and how to register in the microsoft DNS ??
i managed to query from the DNS server after adding /etc/resolve.conf and editing /etc/nsswitch.conf
but i need to register the soalris server (dns Client) into Microsoft DNS automatically.... (3 Replies)
Discussion started by: mduweik
3 Replies
2. UNIX for Advanced & Expert Users
I'd like to get some opnions on choosing DNS server:
Windows DNS vs Linux BIND comparrsion:
1) managment, easy of use
2) Security
3) features
4) peformance
5) ??
I personally prefer Windows DNS server for management, it supports GUI and command line. But I am not sure about security... (2 Replies)
Discussion started by: honglus
2 Replies
3. Solaris
Hi
I am looking to have an NTP server that will support both ipv4 and ipv6 clients. Is there anything specific about the configuration that I should be looking at? (7 Replies)
Discussion started by: eeisken
7 Replies
4. Solaris
hi, i have a Solaris 10 DNS server, how do you check whether it can support IPv6 networking ? (0 Replies)
Discussion started by: Exposure
0 Replies
5. Solaris
I have Bind running on a Solaris box that is our main public DNS. Given my very limited knowledge on DNS, I changed a few of the zones in the DNS to be 'dual-stack'. I did it through Webmin, but I know that I can also do it by adding an AAAA-record to the zone file.
My question is how can I make... (2 Replies)
Discussion started by: Dardeer
2 Replies
6. IP Networking
Hello, i tried to enable IPv6 networking and after service network restart i seen these messages:
FATAL: Error inserting ipv6 (/lib/modules/2.6.18-348.16.1.el5.028stab108.1/kernel/net/ipv6/ipv6.ko): Device or resource busy
CRITICAL : Kernel is not compiled with IPv6 support
Bringing up... (6 Replies)
Discussion started by: postcd
6 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I have created a bonding bond1 interface with 6 Eth , mode=4. Recently i have changed my old ipv6 to new one and tried to restart as well as reload network service. Post which i can see old as well as changed ipv6 in ifconfig command output. Below are few files and command output for your... (1 Reply)
Discussion started by: omkar.jadhav
1 Replies
8. Solaris
Hi,
We have built a new server (RHEL VM)and added that IP/hostname into dns zone configs file on DNS server (Solaris 10). Reloaded the configuration using
and added nameserver into resolv.conf on client. But when I am trying nslookup, its not getting resolved. The nameserver is not able to... (8 Replies)
Discussion started by: snchaudhari2
8 Replies
9. UNIX for Beginners Questions & Answers
When I do simple nslookup it does not generate any query for IPV6 (AAAA). But sometimes I see DNS query for both A and AAAA are generated. What decides this? The reason I do not want AAAA query is in most of the cases AAAA records are absent. Hence, if one DNS server fails, the clients keeps... (1 Reply)
Discussion started by: broy32000
1 Replies
RPING(1) librdmacm RPING(1)
NAME
rping - RDMA CM connection and RDMA ping-pong test.
SYNOPSIS
rping -s [-v] [-V] [-d] [-P] [-a address] [-p port]
[-C message_count] [-S message_size]
rping -c [-v] [-V] [-d] -a address [-p port]
[-C message_count] [-S message_size]
DESCRIPTION
Establishes a reliable RDMA connection between two nodes using the librdmacm, optionally performs RDMA transfers between the nodes, then
disconnects.
OPTIONS
-s Run as the server.
-c Run as the client.
-a address
On the server, specifies the network address to bind the connection to. On the client, specifies the server address to connect to.
-p Port number for listening server.
-v Display ping data.
-V Validate ping data.
-d Display debug information.
-C message_count
The number of messages to transfer over each connection. (default infinite)
-S message_size
The size of each message transferred, in bytes. (default 100)
-P Run the server in persistent mode. This allows multiple rping clients to connect to a single server instance. The server will run
until killed.
NOTES
Because this test maps RDMA resources to userspace, users must ensure that they have available system resources and permissions. See the
libibverbs README file for additional details.
SEE ALSO
rdma_cm(7), ucmatose(1), udaddy(1), mckey(1)
librdmacm 2007-05-15 RPING(1)