Get info on network interface Post: 302122266

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

2. UNIX for Dummies Questions & Answers

I can't remember or figure out how to do this. What is the command(s) in Solaris 8 sparc to show the values operating a NIC, specifically the negotiated transfer rate (10/100) and mode (full/half duplex)? Also, how can I force 100 Mb full (the network is just a crossover cable, and the other box is...

3. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0...

4. IP Networking

How to activate a network interface?

What are the steps between "ifconfig eth0 UP" and "net_device->open"? ifconfig eth0 UP => ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) => ????? => what are these steps? net_device->open Thanks!

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

6. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

7. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT DEBIAN

ifdata

ifdata(1)																 ifdata(1)

NAME

       ifdata - get network interface info without parsing ifconfig output

SYNOPSIS

       ifdata [options] {iface}

DESCRIPTION

       ifdata can be used to check for the existence of a network interface, or to get information abut the interface, such as its IP address. Un-
       like ifconfig or ip, ifdata has simple to parse output that is designed to be easily used by a shell script.

OPTIONS

       -h     Print out a help summary.

       -e     Test to see if the interface exists, exit nonzero if it does not.

       -p     Prints out the whole configuration of the interface.

       -pe    Prints "yes" or "no" if the interface exists or not.

       -pa    Prints the IPv4 address of the interface.

       -pn    Prints the netmask of the interface.

       -pN    Prints the network address of the interface.

       -pb    Prints the broadcast address of the interface.

       -pm    Prints the MTU of the interface.

       Following options are Linux only.

       -ph    Prints the hardware address of the interface.

       -pf    Prints the flags of the interface.

       -si    Prints out all the input statistics of the interface.

       -sip   Prints the number of input packets.

       -sib   Prints the number of input bytes.

       -sie   Prints the number of input errors.

       -sid   Prints the number of dropped input packets.

       -sif   Prints the number of input fifo overruns.

       -sic   Print the number of compressed input packets.

       -sim   Prints the number of input multicast packets.

       -so    Prints out all the output statistics of the interface.

       -sop   Prints the number of output packets.

       -sob   Prints the number of output bytes.

       -soe   Prints the number of output errors.

       -sod   Prints the number of dropped output packets.

       -sof   Prints the number of output fifo overruns.

       -sox   Print the number of output collisions.

       -soc   Prints the number of output carrier losses.

       -som   Prints the number of output multicast packets.

       -bips  Prints the number of bytes of incoming traffic measured in one second.

       -bops  Prints the number of bytes of outgoing traffic measured in one second.

AUTHOR

       Benjamin BAYART

								    2006-03-07								 ifdata(1)

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Discussion started by: witt

2. UNIX for Dummies Questions & Answers

network interface questions

Discussion started by: 98_1LE