06-19-2007
How about looking for the PCI id?
0x14E4 Broadcom Corporation
www.broadcom.com
This should be available in dmesg, may be other places it's available as well.
Eg
Quote:
Run "lspci" and "lspci -n" in an xterminal to find the MANFID number of your card.
If you see 14e4:4318 or 14e4:4320 then your card is Broadcom-based....
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Dummies Questions & Answers
I can't remember or figure out how to do this. What is the command(s) in Solaris 8 sparc to show the values operating a NIC, specifically the negotiated transfer rate (10/100) and mode (full/half duplex)? Also, how can I force 100 Mb full (the network is just a crossover cable, and the other box is... (3 Replies)
Discussion started by: 98_1LE
3 Replies
3. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
4. IP Networking
What are the steps between "ifconfig eth0 UP" and "net_device->open"?
ifconfig eth0 UP =>
ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) =>
????? => what are these steps?
net_device->open
Thanks! (1 Reply)
Discussion started by: samuncle
1 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT MOJAVE
urn-scheme
uri_urn(n) Tcl Uniform Resource Identifier Management uri_urn(n)
__________________________________________________________________________________________________________________________________________________
NAME
uri_urn - URI utilities, URN scheme
SYNOPSIS
package require Tcl 8.2
package require uri::urn ?1.1.2?
uri::urn::quote url
uri::urn::unquote url
_________________________________________________________________
DESCRIPTION
This package provides two commands to quote and unquote the disallowed characters for url using the urn scheme, registers the scheme with
the package uri, and provides internal helpers which will be automatically used by the commands uri::split and uri::join of package uri to
handle urls using the urn scheme.
COMMANDS
uri::urn::quote url
This command quotes the characters disallowed by the urn scheme (per RFC 2141 sec2.2) in the url and returns the modified url as its
result.
uri::urn::unquote url
This commands performs the reverse of ::uri::urn::quote. It takes an urn url, removes the quoting from all disallowed characters,
and returns the modified urls as its result.
BUGS, IDEAS, FEEDBACK
This document, and the package it describes, will undoubtedly contain bugs and other problems. Please report such in the category uri of
the Tcllib SF Trackers [http://sourceforge.net/tracker/?group_id=12883]. Please also report any ideas for enhancements you may have for
either package and/or documentation.
KEYWORDS
rfc 2141, uri, url, urn
CATEGORY
Networking
uri 1.1.2 uri_urn(n)