Get info on network interface Post: 302122244

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

2. UNIX for Dummies Questions & Answers

I can't remember or figure out how to do this. What is the command(s) in Solaris 8 sparc to show the values operating a NIC, specifically the negotiated transfer rate (10/100) and mode (full/half duplex)? Also, how can I force 100 Mb full (the network is just a crossover cable, and the other box is...

3. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0...

4. IP Networking

How to activate a network interface?

What are the steps between "ifconfig eth0 UP" and "net_device->open"? ifconfig eth0 UP => ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) => ????? => what are these steps? net_device->open Thanks!

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

6. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

7. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT NETBSD

ubsec

UBSEC(4)						   BSD Kernel Interfaces Manual 						  UBSEC(4)

NAME

     ubsec -- Broadcom and BlueSteel uBsec 5x0x crypto accelerator

SYNOPSIS

     ubsec* at pci? dev ? function ?

DESCRIPTION

     The ubsec driver supports cards containing any of the following chips:

	   Bluesteel 5501    The original chipset, no longer made.  This extremely rare unit was not very fast, lacked an RNG, and had a number of
			     other bugs.

	   Bluesteel 5601    A faster and fixed version of the original, with a random number unit and large number engine added.

	   Broadcom BCM5801  A BCM5805 without public key engine or random number generator.

	   Broadcom BCM5802  A slower version of the BCM5805.

	   Broadcom BCM5805  Faster version of Bluesteel 5601.

	   Broadcom BCM5820  64 bit version of the chip, and significantly more advanced.

	   Broadcom BCM5821  Faster version of the BCM5820.  (This is the chip found on the Sun Crypto Accelerator 1000.)

	   Broadcom BCM5822  Faster version of the BCM5820.

	   Broadcom BCM5823  Faster version of the BCM5822.

	   Broadcom BCM5823  Faster version of the BCM5821, with AES hardware.

     The ubsec driver registers itself to accelerate DES, Triple-DES, MD5, SHA1, MD5-HMAC, and SHA1-HMAC operations for opencrypto(9), and thus
     for fast_ipsec(4) and crypto(4).

     On those models which contain a public key engine (almost all of the more recent ones), this feature is registered with the crypto(4) subsys-
     tem.

     On all models except the Bluesteel 5501 and Broadcom 5801, the driver registers itself to provide random data to the rnd(4) subsystem.

SEE ALSO

     crypto(4), fast_ipsec(4), intro(4), rnd(4), opencrypto(9)

HISTORY

     The ubsec device driver appeared in OpenBSD 2.8.  The ubsec device driver was imported to FreeBSD 5.0, back-ported to FreeBSD 4.8, and subse-
     quently imported to NetBSD 2.0.

BUGS

     The BCM5801 and BCM5802 have not actually been tested.

     Whilst some of the newer chips support AES, AES is not supported by the driver.

BSD
								   June 10, 2000							       BSD

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Discussion started by: witt

2. UNIX for Dummies Questions & Answers

network interface questions

Discussion started by: 98_1LE