Get info on network interface Post: 302122238

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

2. UNIX for Dummies Questions & Answers

I can't remember or figure out how to do this. What is the command(s) in Solaris 8 sparc to show the values operating a NIC, specifically the negotiated transfer rate (10/100) and mode (full/half duplex)? Also, how can I force 100 Mb full (the network is just a crossover cable, and the other box is...

3. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0...

4. IP Networking

How to activate a network interface?

What are the steps between "ifconfig eth0 UP" and "net_device->open"? ifconfig eth0 UP => ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) => ????? => what are these steps? net_device->open Thanks!

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

6. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

7. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT PHP

tc-matchall

Match-all classifier in tc(8)					       Linux					     Match-all classifier in tc(8)

NAME

       matchall - traffic control filter that matches every packet

SYNOPSIS

       tc filter ... matchall [ skip_sw | skip_hw  ] [ action ACTION_SPEC ] [ classid CLASSID ]

DESCRIPTION

       The matchall filter allows to classify every packet that flows on the port and run a action on it.

OPTIONS

       action ACTION_SPEC
	      Apply an action from the generic actions framework on matching packets.

       classid CLASSID
	      Push matching packets into the class identified by CLASSID.

       skip_sw
	      Do  not  process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter-
	      face, operation will fail.

       skip_hw
	      Do not process filter by hardware.

EXAMPLES

       To create ingress mirroring from port eth1 to port eth2:

	      tc qdisc	add dev eth1 handle ffff: ingress
	      tc filter add dev eth1 parent ffff:	    
		      matchall skip_sw			    
		      action mirred egress mirror	    
		      dev eth2

       The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it  that
       mirrors the packets to device eth2.

       To create egress mirroring from port eth1 to port eth2:

	      tc qdisc add dev eth1 handle 1: root prio
	      tc filter add dev eth1 parent 1:		     
		      matchall skip_sw			     
		      action mirred egress mirror	     
		      dev eth2

       The  first  command  creats  an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a
       matchall filters on it that mirrors the packets to device eth2.

       To sample one of every 100 packets flowing into interface eth0 to psample group 12:

	      tc qdisc add dev eth0 handle ffff: ingress
	      tc filter add dev eth0 parent ffff: matchall 
		   action sample rate 100 group 12

SEE ALSO

       tc(8),

iproute2							    21 Oct 2015 				     Match-all classifier in tc(8)

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Discussion started by: witt

2. UNIX for Dummies Questions & Answers

network interface questions

Discussion started by: 98_1LE