Sponsored Content
Operating Systems Linux Get info on network interface Post 302122235 by aleksey on Tuesday 19th of June 2007 06:18:16 PM
Old 06-19-2007
Get info on network interface

Hello everybody,

How can link network interface to the output of lspci -vv. Basicly i need to know who is the manufacturer of a specific interface, for example eth0 {Is it an Intel, or Broadcome, or something else}. Is there a way to find that out?

Thanx
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. UNIX for Dummies Questions & Answers

network interface questions

I can't remember or figure out how to do this. What is the command(s) in Solaris 8 sparc to show the values operating a NIC, specifically the negotiated transfer rate (10/100) and mode (full/half duplex)? Also, how can I force 100 Mb full (the network is just a crossover cable, and the other box is... (3 Replies)
Discussion started by: 98_1LE
3 Replies

3. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies

4. IP Networking

How to activate a network interface?

What are the steps between "ifconfig eth0 UP" and "net_device->open"? ifconfig eth0 UP => ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) => ????? => what are these steps? net_device->open Thanks! (1 Reply)
Discussion started by: samuncle
1 Replies

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

6. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

7. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
sg_get_network_iface_stats(3)				     Library Functions Manual				     sg_get_network_iface_stats(3)

NAME
sg_get_network_iface_stats - get network interface statistics SYNOPSIS
#include <statgrab.h> sg_network_iface_stats *sg_get_network_iface_stats(int *entries); DESCRIPTION
The sg_get_network_iface_stats function takes a pointer to an int, entries, which is filled with the number of network interfaces the machine has. This is needed to know how many sg_network_iface_stats structures have been returned. A pointer is returned to the first sg_network_iface_stats. sg_get_network_iface_stats returns statistics about the network interfaces in the machine. Specifically, it returns the speed of the inter- face, the duplex state, and whether it is currently up. RETURN VALUES
The sg_get_network_iface_stats returns a pointer to a structure of type sg_network_iface_stats. typedef enum{ SG_IFACE_DUPLEX_FULL, SG_IFACE_DUPLEX_HALF, SG_IFACE_DUPLEX_UNKNOWN }sg_iface_duplex; Note: The SG_IFACE_DUPLEX_UNKNOWN value could mean that duplex hasn't been negotiated yet. typedef struct{ char *interface_name; int speed; sg_iface_duplex duplex; int up; }sg_network_iface_stats; interface_name The name known to the operating system. (eg. on linux it might be eth0) speed The speed of the interface, in megabits/sec. duplex The duplex state the interface is in. See sg_iface_duplex for permitted values. up Whether the interface is up. SEE ALSO
statgrab(3) WEBSITE
http://www.i-scream.org/libstatgrab/ i-scream $Date: 2005/07/13 09:31:53 $ sg_get_network_iface_stats(3)
All times are GMT -4. The time now is 03:15 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy