Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
i purchased, what was labeled as a 4-port fast ethernet sbus card from ebay.
i installed it in my ultra1, and it seems to be working fine. how can i determine if the card is infact a fast ethernet card vs. the standard ethernet 4-port card? (7 Replies)
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Hi guys,
Suppose you have a server with two ethernet cards (1GB each) and each cards are connecting to two different switches cisco 3750. My question is:
How can I setup my server's network interfaces to increase the throughput up to 2GB? is it possible? If not, do you know another way to up... (3 Replies)
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Hello.
I have a server RS/6000 with AIX 4.2. The server have a network card with 10/100mbps speed, but for some reason, the ethernet only runs at 10Mbps, it doesn,t matter if I put the net cable on a 100Mbps switch, it keeps running at 10Mbps speed....
I know how to view/change ethernet speed... (1 Reply)
Discussion started by: little_ball
1 Replies
LEARN ABOUT REDHAT
xirc2ps_cs
XIRC2PS_CS(4) Kernel Interfaces Manual XIRC2PS_CS(4)NAME
xirc2ps_cs - Xircom CE2ps (and newer) device driver
SYNOPSIS
insmod xirc2ps_cs.o [pc_debug=n] [full_duplex=n] [irq_list=i,j,...] [if_port=n] [lockup_hack=n]
DESCRIPTION
xirc2ps_cs is the low-level Card Services driver for the Xircom 16-bit PCMCIA ethernet adapters. When this driver is attached to a card,
it allocates the next available ethernet device.
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
if_port=n
Selects the transceiver type, for some CE3B-100 cards that lack the ability to autonegotiate. For such cards, a value of 1 selects
10baseT, and 4 selects 100baseT.
full_duplex=n
Selects full duplex mode. The default is 0 (half duplex).
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
lockup_hack=n
Enables a hack to avoid lockups on some cards. Use this only if you really have lockup problems with your card.
SEE ALSO cardmgr(8), pcmcia(5).
BUGS
Please report to <xircom-bugs@isil.d.shuttle.de>
AUTHOR
Werner Koch <werner.koch@guug.de>
1.5 1998/09/15 12:40:59 XIRC2PS_CS(4)