06-04-2007
unix booting problem
I am working as an engineer at Department of Civil Aviation in Myanmar.We use AlphaServer 800 5/333 for Radar System.Operating System is Unix....
Now, it shows errors during startup procedure..These errors are.....
***Hard Error -Error#5-
Diagnostic Name ID Device Pass Test Hard/Soft 4-Jun-2055
exer_kid 0000014d 0 0 1 0 11:16:49
Error in read of 0 bytes at location 00003C00 from device dkb200.2.0.12.0
***End of Error*** dkb100.1.0.12.0
Starting LSM
cam_logger:CAN_ERROR packet
cam_logger:bus 1 target 1 lun0
cdisk_check_sense
Device aborted command - parity error?
Hard Error Detected
DEC RZ1BB-CS (C) DEC0844
Active CCB at time of error
CCB request completed with an error
Error,exception,or abnormal condition
ABORTED COMMAND - Target aborted command
Above errors show again and again and it startup.But it restarts within 1 min.And it shows errors...
!!!!FTF FATAL ERROR DETECTED.
--->SD MGR,mount;Error:2,No such file or directory
!!!!This NODES IS GOING TO CRASH!!!!
CP-SAVE_TERM routine to be called
CP_SAVE_TERM exited with hlt_req=1,
ro=00000000.00000000
who could explain me about that problem?
9 More Discussions You Might Find Interesting
1. HP-UX
Hi,
where can i get Hp unix dummy version to use in my home system.iam a newbie to unix.pls let me know if any avilable..Thank you Shruti (6 Replies)
Discussion started by: shruti_mgp
6 Replies
2. AIX
HI Everybody,
I am a newbie of using AIX, would you mind telling me how to setup JOE and OpenSSH in AIX 5L 5.3. Thanks!
Hugo (0 Replies)
Discussion started by: tknl
0 Replies
3. UNIX for Dummies Questions & Answers
hi,
im new to unix.i dont have unix software in my system.
Is there any website is there to practice unix in online
can u please any one help me......
thanks in advance (3 Replies)
Discussion started by: gowridoc
3 Replies
4. AIX
HI Guys,
I have AIX 5.3 with TL05 ...I am trying to install HDLM 5.80/5.81 on this.
Installed Hitachi.aix.support.rte file set.
HDLM kept on installing ...it is not comming out .command status is "running"
============================================
Command: running stdout: yes ... (0 Replies)
Discussion started by: b_manu78
0 Replies
5. UNIX for Dummies Questions & Answers
Hi All,
From where can i get the UNIX Software so that i can install the same in my Laptop.
Thanks
Dilip (2 Replies)
Discussion started by: DilipPanda
2 Replies
6. Solaris
Estou tentando instalar o software de HDLM ( Hitachi Dynamic Link Manager ) e está apresentando a seguinte mensagem:
-bash-3.00# ./installhdlm
KAPL09187-W No parameter is specified.
Não sei que parameter é esse ? (1 Reply)
Discussion started by: to.brunoaugusto
1 Replies
7. Solaris
I'm trying to install the software HDLM (Hitachi Dynamic Link Manager) and is presenting the following message:
-Bash-3.00 #./Installhdlm
In KAPL09187-W parameter is specified.
I do not know which parameter is that? (3 Replies)
Discussion started by: to.brunoaugusto
3 Replies
8. AIX
Hi to all
please help ...Acutally i m new in AIX. I dont much know about AIX. I m totally confusing with software management chapter. Actually i m not getting difference between.
LPP,,BUNDLE,,,PACKAGE,,FIXES,,,APAR,,,,,FILESET.....
i read in the book.......as i know about RPM in linux.....but in... (2 Replies)
Discussion started by: life008
2 Replies
9. Solaris
hi all
i am working on zone and when i try to install software
i face read and write permisssion on directory which zonning inherit from them
so how can i add read and write permission to zone already running (3 Replies)
Discussion started by: jamisux
3 Replies
startup(7) Miscellaneous Information Manual startup(7)
NAME
startup - event signalling system startup
SYNOPSIS
startup [ENV]...
DESCRIPTION
The startup event is generated by the Upstart init(8) daemon after it has completed its own initialisation and is the signal that the rest
of the system may be started.
Typically this will involve checking and mounting the partitions and drives that form the filesystem, loading drivers for connected devices
and starting the X windowing system or other login environment.
In the default Upstart configuration, the primary task run on the startup event is the /etc/init/rc-sysinit.conf job responsible for gener-
ating the System V compatible runlevel(7) event. See that page for a more detailed explanation of this process.
Paradoxically there is currently no corresponding Upstart-native event signifying that the system is to be shutdown, only the System V com-
patible runlevel 0 and runlevel 6 events provide this functionality.
EXAMPLE
A service with no other dependencies run on startup might use:
start on startup
SEE ALSO
runlevel(7) init(8)
Upstart 2009-07-09 startup(7)