Sponsored Content
Full Discussion: unix software problem
Top Forums UNIX for Advanced & Expert Users unix software problem Post 302120105 by akzin on Monday 4th of June 2007 06:00:45 AM
Old 06-04-2007
unix booting problem

I am working as an engineer at Department of Civil Aviation in Myanmar.We use AlphaServer 800 5/333 for Radar System.Operating System is Unix....
Now, it shows errors during startup procedure..These errors are.....
***Hard Error -Error#5-
Diagnostic Name ID Device Pass Test Hard/Soft 4-Jun-2055
exer_kid 0000014d 0 0 1 0 11:16:49
Error in read of 0 bytes at location 00003C00 from device dkb200.2.0.12.0
***End of Error*** dkb100.1.0.12.0
Starting LSM
cam_logger:CAN_ERROR packet
cam_logger:bus 1 target 1 lun0
cdisk_check_sense
Device aborted command - parity error?
Hard Error Detected
DEC RZ1BB-CS (C) DEC0844
Active CCB at time of error
CCB request completed with an error
Error,exception,or abnormal condition
ABORTED COMMAND - Target aborted command
Above errors show again and again and it startup.But it restarts within 1 min.And it shows errors...
!!!!FTF FATAL ERROR DETECTED.
--->SD MGR,mount;Error:2,No such file or directory
!!!!This NODES IS GOING TO CRASH!!!!
CP-SAVE_TERM routine to be called
CP_SAVE_TERM exited with hlt_req=1,
ro=00000000.00000000

who could explain me about that problem?
 

9 More Discussions You Might Find Interesting

1. HP-UX

Hp Unix software

Hi, where can i get Hp unix dummy version to use in my home system.iam a newbie to unix.pls let me know if any avilable..Thank you Shruti (6 Replies)
Discussion started by: shruti_mgp
6 Replies

2. AIX

Software Installation Problem

HI Everybody, I am a newbie of using AIX, would you mind telling me how to setup JOE and OpenSSH in AIX 5L 5.3. Thanks! Hugo (0 Replies)
Discussion started by: tknl
0 Replies

3. UNIX for Dummies Questions & Answers

how to practice unix in online without unix software

hi, im new to unix.i dont have unix software in my system. Is there any website is there to practice unix in online can u please any one help me...... thanks in advance (3 Replies)
Discussion started by: gowridoc
3 Replies

4. AIX

having problem with HDLM software installation

HI Guys, I have AIX 5.3 with TL05 ...I am trying to install HDLM 5.80/5.81 on this. Installed Hitachi.aix.support.rte file set. HDLM kept on installing ...it is not comming out .command status is "running" ============================================ Command: running stdout: yes ... (0 Replies)
Discussion started by: b_manu78
0 Replies

5. UNIX for Dummies Questions & Answers

UNIX Software

Hi All, From where can i get the UNIX Software so that i can install the same in my Laptop. Thanks Dilip (2 Replies)
Discussion started by: DilipPanda
2 Replies

6. Solaris

Problem installing the software HDLM

Estou tentando instalar o software de HDLM ( Hitachi Dynamic Link Manager ) e está apresentando a seguinte mensagem: -bash-3.00# ./installhdlm KAPL09187-W No parameter is specified. Não sei que parameter é esse ? (1 Reply)
Discussion started by: to.brunoaugusto
1 Replies

7. Solaris

Problem installing the software HDLM

I'm trying to install the software HDLM (Hitachi Dynamic Link Manager) and is presenting the following message: -Bash-3.00 #./Installhdlm In KAPL09187-W parameter is specified. I do not know which parameter is that? (3 Replies)
Discussion started by: to.brunoaugusto
3 Replies

8. AIX

AIX software management problem

Hi to all please help ...Acutally i m new in AIX. I dont much know about AIX. I m totally confusing with software management chapter. Actually i m not getting difference between. LPP,,BUNDLE,,,PACKAGE,,FIXES,,,APAR,,,,,FILESET..... i read in the book.......as i know about RPM in linux.....but in... (2 Replies)
Discussion started by: life008
2 Replies

9. Solaris

Zoning permission problem when installing software

hi all i am working on zone and when i try to install software i face read and write permisssion on directory which zonning inherit from them so how can i add read and write permission to zone already running (3 Replies)
Discussion started by: jamisux
3 Replies
Config::Scoped::Error(3pm)				User Contributed Perl Documentation				Config::Scoped::Error(3pm)

NAME
Config:Scoped::Error - an exception class hierarchy based on Error.pm for Config::Scoped SYNOPSIS
use Config::Scoped::Error; Config::Scoped::Error::Parse->throw( -text => $parser_error, -file => $config_file, -line => $thisline, ); Config::Scoped::Error::IO->throw( -text => "can't open file: $!", -file => $config_file, -line => $thisline, ); Config::Scoped::Error::Validate::Macro->throw( -text => "macro redefinition: $macro_name", -file => $config_file, -line => $thisline, ); DESCRIPTION
Config::Scoped::Error is a class hierarchy based on Error.pm. The following Exception class hierarchy is defined: Config::Scoped::Error Config::Scoped::Error::Parse Config::Scoped::Error::Validate Config::Scoped::Error::Validate::Macro Config::Scoped::Error::Validate::Parameter Config::Scoped::Error::Validate::Declaration Config::Scoped::Error::Validate::Permissions Config::Scoped::Error::IO SEE ALSO
Config::Scoped, Error AUTHOR
Karl Gaissmaier <karl.gaissmaier at uni-ulm.de> COPYRIGHT AND LICENSE
Copyright (c) 2004-2008 by Karl Gaissmaier This library is free software; you can redistribute it and/or modify it under the same terms as Perl itself. perl v5.14.2 2012-03-16 Config::Scoped::Error(3pm)
All times are GMT -4. The time now is 04:49 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy